Intended use
This machine is primarily intended for the sawing, longitudinally and transversely, of solid wood,
chipboard, plywood, alum1n1um, tiles and stone held in a fixed position. Please note that the blade
pre-installed in the saw as supplied is intended for use with wood only. Any other use or modification
to the device shall be considered as improper use and could give rise to considerable dangers It is not
suitable for commercial use
Function Description
The numbering of the products features refers to the illustration of the machine on the graphics page.
b)
c)
d)
e)
f)
g)
4)
a)
b)
c)
d)
e)
f)
g)
5)
Have your power tool serviced by a qualified repair person using only identical replacement parts.
This will ensure that the safety of the power tool is maintained.
DANGER: Keep hands away from cutting area and the blade.
a)
b)
●
●
●
WARNING:
Some dust created by power sanding, sawing, grinding, drilling, and other construc-
tion activities contains chemicals known in the state of California to cause cancer, birth defects or other
reproductive harm. Some examples of these chemicals are:
●
Your risk from these exposures varies, depending on how often you do this type of work. To reduce
your exposure to these chemicals: work in a well ventilated area, and work with approved safety
equipment, such as those dust masks that are specially designed to filter out microscopic particles.
WARNING:
ALWAYS USE SAFETY GLASSES. Everyday eyeglasses are NOT safety glasses.
Also use face or dust mask if cutting
●
WARNING:
Cutting plastics, sap coated wood, and other materials may cause melted material
to accumulate on the blade tips and the body of the saw blade, increasing the risk of blade overheat-
ing and binding while cutting.
WARNING:
Use of this tool can generate and/or disburse dust, which may cause serious and
permanent respiratory or other injury. Always use NIOSH/OSHA approved respiratory protection
appropriate for the dust exposure. Direct particles away from face and body. Always operate tool in
well-ventilated area and provide for proper dust removal. Use dust collection system wherever
possible.
EN
FR
ES
DEFINITIONS: SAFETY ALERT SYMBOLS AND WORDS
It is important for you to read and understand this manual. The information it contains relates to
protecting YOUR SAFETY and PREVENTING PROBLEMS. The symbols below are used to help you
recognize this information.
NOTICE:
Used without the safety alert symbol indicates potentially hazardous situation which, if not
avoided, may result in property damage.
WARNING: Read all safety warnings and all instructions.
Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury.
SAVE ALL WARNINGS AND INSTRUCTIONS FOR FUTURE REFERENCE
The term “power tool” in the warnings refers to your mains operated (corded) power tool or battery-op-
erated (cordless) power tool.
1)
a)
b)
c)
2)
a)
b)
c)
d)
e)
f)
3)
a)
c)
d)
e)
f)
g)
h)
Causes and Operator Prevention of Kickback:
●
●
●
Kickback is the result of saw misuse and/ or incorrect operating procedures or conditions and can be
avoided by taking proper precautions as given below:
a)
b)
c)
d)
e)
f)
g)
Lower Guard Safety Instructions
a)
b)
c)
d)
Additional Safety Instructions
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
The smaller the gauge number of the wire, the greater the capacity of the cable, that is 16 gauge has
more capacity than 18 gauge. An undersized cord will cause a drop in line voltage resulting in loss of
power and overheating. When using more than one extension to make up the total length, be sure
each individual extension contains at least the minimum wire size. The following table shows the
correct size to use depending on cord length and nameplate ampere rating. If in doubt, use the next
heavier gauge. The smaller the gauge number, the heavier the cord.
The label on your tool may include the following symbols. The symbols and their definitions are as
follows:
Safety Rules for Laser Lights
The laser light/laser radiation used in the system is Class 2 with maximum 1mW and 650nm
wavelengths. These lasers do not normally present an optical hazard, although staring at the beam
may cause flash blindness.
WARNING : Do not stare directly at the laser beam.
A hazard may exist if you deliberately stare into the beam, please observe all safety rules as follows;
●
●
●
●
●
CAUTION:
Use of controls or adjustments or performance of procedures other than those
specified herein may result in hazardous radiation exposure
Assembly/Adjustment setup
WARNING:
Before any work on the power tool, always remove the plug from the power source.
●
●
●
Installing the Saw Blade
1.
2.
3.
4.
5.
Removal the Saw Blade
1.
2.
3.
4.
Adjust the cutting depth,
1.
2.
Note: if possible, recommend to setup the cutting depth approximately 2mm deeper than material
thickness, this should help to ensure you achieve a clean cut.
CHANGING THE LASER BATTERIES (see pic. J)
The batteries that operate the laser will have to be replaced after considerable use of the laser.
1.
2.
3.
4.
DANGER:
Never allow the laser beam to shine into a person's eyes, Serious eye damage could
result. Make sure the laser switch is OFF and the laser is NOT pointing toward you while replacing the
laser batteries and when checking the laser function.
Application
The mini plunge saw is a versatile one that allows you to cut many different types of materials. Some
of the materials include
Switching On and Off
(see pic. H)
To start the machine
●
First push the lock-off button (5) backward.
●
Then press the switch trigger (4) and keep it pressed.
●
When cut the wood, put the machine on the
workpiece and push it along the wood.
To switch off the machine
●
First take out of the machine from workpiece.
●
Then release the switch trigger.
Note: For safety reasons, the On/Off switch
cannot be locked; it must remain pressed during
the entire operation.
Laser function (see pic. I)
Note: Laser light can cause severe eye damage.
Never look directly into the laser beam. Do not
point the laser beam at other people or animals,
either directly or through reflective surfaces.
The laser feature on your saw is powered by two
LR44 1.5V button batteries (installed).
The Laser feature clearly shows you an extend-
ed cut-line, even over debris on the work piece.
●
Turn it on with the laser light ON/Off switch right
before cutting.
●
Turn it off immediately after use to conserve
battery and laser life.
5.Replace with two new batteries.
NOTES:
a)Use two 1.5V LR 44 batteries
b)install the batteries with the"+" side (18) of the
batteries facing the rear of the tool
6. Re-install the laser cover and fasten it in place
with the laser cover screw.
Turn the laser switch off.
Remove the laser cover screw.
Lift the laser cover off the top of the laser assembly,
Remove the two old batteries (17).
●
●
●
Blade selection
MAINTENANCE
WARNING:
Unplug tool before installing or removing accessories, before adjusting, or when
making repairs. Use only mild soap and damp cloth to clean the tool. Never let any liquid get inside
the tool; never immerse any part of the tool into a liquid.
IMPORTANT:
To assure product SAFETY and RELIABILITY, repairs, maintenance and adjust-
ment (other than those listed
in this manual) should be performed by authorized service centers or other qualified service organiza-
tions, always using identical replacement parts.
Wood products such as lumber, hardwood, plywood, composition board and paneling
plastic and soft metal.
tile and backerboard
- 09 -
Technology Creates Power
