background image

36 

software (Winpower, etc.). 

2)  It is attention that the transfer time 

of  UPS  output  from  HE  mode  to 

battery mode is about 10ms. But it 

is  still  too  long  for  some  sensitive 

load. 

Fig 5-8 

Converter mode 

In converter mode, the UPS would free 

run  with  fixed  output  frequency  (50Hz 

or  60Hz).  Once  the  mains  is  loss  or 

abnormal,  the  UPS  would  transfer  to 

battery mode  and  the  load  is  supplied 

continuously. 

1)  The  function  could  be  enabled 

through  the  LCD  setting  or  the 

software (Winpower, etc.). 

2)  The  load  have  to  be  derated  to 

80% in converter mode. 

Fig 5-9 

Warning: 

When the warning occurs, it illustrates 

that 

there 

are 

some 

abnormal 

problems during the operation of UPS. 

Normally  the  problems  are  not  fatal 

and  the  UPS  continues  working,  but 

they should be paid attention to, or the 

UPS may fail. 

Fig 5-10 

Fault: 

When the fault occurs, it illustrates that 

some  fatal  problems  happened,  the 

UPS would directly cut off the output or 

transfer to bypass, and keep alarming. 

The  backlight  of  LCD  would  also  turn 

to red.   

37 

Fig 5-11 

Overload: 

When  the  UPS  is  overload,  the  alarm 

will  beep  twice  every  second.  Some 

unnecessary loads should be get rid of 

one  by  one  to  decrease  the  loads 

connected to the UPS. 

 

Fig 5-12 

Battery Test 

UPS is executing a battery test

 

Fig 5-13 

Battery fail: 

if the battery status detected is “bad 

battery detected” or “battery 

disconnected”, the symbol of battery 

failure would be shown and UPS would 

alarm. 

 

5.3 Turning on and Turning off UPS   

Attention: 

The UPS could only be turning on while connecting with the 

utility for the first time. 

Attention:

 Please switch off the connected loads at first before turning 

on the UPS, and switch on the loads one by one after the UPS is turned 

on. Switch off all of the connected loads before turning off the UPS. 

5.3.1 Turning on UPS with utility 

1)  Check all the connection is correct.   

2)  Power on the UPS, the fan begins to rotate, LCD will switch-ON. 

After that, the LCD will show the default UPS status summary 

screen. 

3)  Pressing 

  button  continuously  for  more  than  1  second,  the 

buzzer will beep 1s, UPS starts to turn on. 

Summary of Contents for AP160N-6K


































Reviews: