background image

 

- 3 - 

Warning 

You must read this handbook before using the appliance. 

Handbook symbols 

Product security 

The text in a box refers to a product safety instruction. 

User safety 

 This symbol associated with any text in a white area characterizes a 

critical instruction for user safety. 

Authorized persons 

Installation, utilization, maintenance 

 This  appliance  is  not  intended  for  use  by  persons  (including  children)  with  reduced  physical,  sensory  or 

mental  capabilities,  or  lack  of  experience  and  knowledge,  unless  they  are  supervised  and  received  adequate 
instructions concerning use of the appliance by a person responsible for their safety. 

Children should be supervised to ensure that they do not play with the appliance. 

Product delivery and general conditions of use 

Appliance and spare parts travel by recipient’s own risks, whatever the delivery method used. If the recipient sees any 

damage  due  to  transport,  he  must  record  it  on  the  delivery  note  and  confirm  it  by  registered  mail  detailing  the 
damage to the carrier, within the following 48 hours. 

The  heat  pump  referred  to  in  this  handbook  is  designed  and  built  solely  for  private  swimming  pool  use.  Tebas 

dissociates its responsibility if used in any other application. 

This handbook is considered as a part of the pool heat pump. It must be read and adhered to before the installation 

and use of the appliance. 

All security instructions highlighted in this manual must be strictly respected. 

Before any connection is made, it is necessary to be sure that the pool heat pump is correctly sized and suitable for 

the pool installation. 

Before  any  electrical  connection  is  made,  it  is  necessary  to  be  sure  that  the  power  supply  cable  conforms  to  the 

manufacturers stated requirements. 

Before  proceeding  with  any  maintenance,  service  or  reparation  work,  the  product  must  be  isolated  from  the  main 

electric supply terminal. Only qualified personnel should carry out these tasks. 

Tebas is released from any responsibility concerning damage caused by non-compliance to the provided instructions, 

errors of handing, installation or usage. 

You  shouldn’t  install  the  heat  pump  in  corrosive  background,  close  to  the  sea,  exposed  to  salt fog,  near  a  chlorine 

storage room or other corrosive chemicals. 

This handbook can be modified without notice. 

 

 

Summary of Contents for INVERTER M















Reviews: