background image

and  the  counter  station  within  the  range  its  receiver  will  be  opened,  too.  The 
communication  can  begin  now.  DTMF  operation  is  possible  in  both  types  of 
modulation. We recommend the use of FM because of the better safety against 
disturbance.  

12. Battery backup : 

As long as the 

TEAM  SelCom 4040

 is connected without any interruption to a 

car battery or a switched on power supply the memory contents of selective call 
codes  and  channels  will  be  kept  stored,  even  when  it  is  switched  off  at 

(  2  ) 

[ VOLUME  /  ON  ]

.  In  addition  it  contains  an  built-in  rechargeable  button  cell 

which will only be charged when the unit is in operation. According to the periods 
of    running  and  the  periods  of  not working  the  charging  condition may be  quite 
different.  So  it  is  recommended  to  keep  an  eye  on  a  reasonable  charging  time 
before  writing  to  the  memories.  A  completely  charged  battery  can  keep  the 
memory contents stored for up to 100 hours even when the unit is disconnected 
from every power source. 

13. Servicing the  TEAM  SelCom 4040 :  

There are no user adjustable or user serviceable parts inside the radio. The cas-
ing must not be opened. Independent repairs or adjustments must not be carried 
out, since each modification or unauthorised intervention will immediately cancel 
all  and  any  guarantee  or  repair  claims,  they  are  also  likely  to  result  in  noncon-
formity to approval regulations which will render  the set illegal. In the event of a 
defect becoming apparent, contact a properly equipped and authorised dealer. 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

- 18 - 

Summary of Contents for SelCom 4040












Reviews: