●
This product is for indoor use but not suitable for outdoor
use.
●
Please use this product in dry condition instead of
exposing it in drips or in high humidity.
●
Do not place this product near any equipment that
generates heat, such as heaters, electric heaters, gas
burners, or other heat-generating equipment.
●
Do not disassemble the electric curtain controller
yourself.
●
Do not use foreign objects to insert the Micro-B receiving
port of the electric curtain controller.
●
Please use the electric curtain controller properly to
avoid damage by collision and dropping from high place.
●
If the electric curtain controller is damaged or deformed,
it should be replaced.
●
Do not use chemical/corrosive/solvent or bleach to clean
the electric curtain controller as this may damage the
housing of it. Please wipe it with a dry and clean cloth.
v��
DC electric curtain controller (RJ)/RX-DDMRJ-1
User Guide/Warranty
●
The product complies with NCC Administrative Regula-
tions on Low Power Radio Waves Radiated Devices
：
Article 12
：
Without permission granted by the NCC,
any company, enterprise, or user is not allowed to
change frequency, enhance transmitting power or alter
original characteristic as well as performance to an
approved low power radio-frequency devices.
Article 14
：
The low power radio-frequency devices
shall not influence aircraft security and interfere legal
communications; If found, the user shall cease operating
immediately until no interference is achieved.
The said legal communications means radio communi-
cations is operated in compliance with the Telecommu-
nications Act. The low power radio-frequency devices
must be susceptible with the interference from legal
communications or ISM radio wave radiated devices.
●Indication of safety marks: If recommended precautions
and safe operating methods are not followed, physical
injury and damage of electrical appliances may be caused.
Precautions for safe use
Package contains
DC electric curtain controller (RJ)*1
User Guide *1
Components of RX-DDMRJ-1
5
6
7
3
4
2
1
Micro USB
DC IN
1
2
3
4
5
6
7
CLOSE(yellow)
STOP (red)
OPEN (brown)
COM (green)
GND
DC power
Power input
CN1 power input
CN2 control terminals
Function
DC 12V~24V
Function
Connect to earth
DC 12V~24V
Function
CLOSE/Rotate
STOP/Rotate
OPEN/Rotate
Universal terminal
＊
Pins of control terminals are
sorted from right to left.
＊
Please choose either power
input DC IN or CN1, do not insert
both kinds of terminals at the
same time.
＊
The function of rotation needs
to operate in coordination with
the control system of electric
curtain control.
＊
Micro USB is the receiving
port used for burning from TX.
Instructions of usage
PC-Tx Mode
Tx-Rx Mode
Tx-Tx TxSide
Tx-Tx RxSide
PC-Tx Mode
Import OK
1
Use PCtools to add the layout of "DC electric curtain
controller (RJ)" with preferred nomination, for example:
Living room curtain, then using USB cable to connect
PCtools and Smart remote controller. Then long press
the “SET” button of the Smart remote controller to
enter into the setting option. After selecting “Data
transmitting/importing”, please press ”ON” button (or
use Hotkey: SET + Up direction button) as shown below
to write the layout to the Smart remote controller:
2
Connect the Smart remote controller (Type A transmit-
ting terminal) and the corresponding electric curtain
controller (Micro-B receiving terminal) simultaneously
using the USB cable as shown below. After selecting
the control point (for example: Living room curtain) to
which you want to burn the electric curtain controller,
press the “SET” button of the Smart remote controller
to enter into the setting option, select “Rx Burn” and
press “ON” button (or use Hotkey: SET + Down
direction button). The setting program will start
automatically. When the setting is completed, the
screen of Smart remote controller will display success
and return to the layout menu as shown below.
