Team Losi 1/10 HIGHroller User Manual Download Page 10 | Manualshive

Page: 10 / 32

background image

0

TM

Battery Pack(s)

To install the battery pack remove the battery hold-down strap by removing the clip from the front mounting boss, and then, while
lifting the strap, pulling forward in one motion.

After you have inserted the fully-charged battery pack reinstall the battery hold-down strap.

Notice that the battery hold-down has a flat side while the other side has strengthening ribs; the rib side should be facing
down to the battery.

Insert on an angle into the rear support, and then down on the front pin and secure it with the previously removed clip.

«
...
8
9
10
11
12
...
»

Summary of Contents for 1/10 HIGHroller

































Reviews:

No comments

Related manuals for 1/10 HIGHroller

Brand: Team C Pages: 34

Brand: TEAMCRACING Pages: 33

Brand: Xray Pages: 40

Brand: Team Durango Pages: 20

1/8 Luxury racing truggy

Brand: Xray Pages: 44

DodgeViper GTSR Supercharged Racer 60-4340

Brand: Radio Shack Pages: 8

CHILDREN'S ELECTRIC RIDE-ON A

Brand: HOMCOM Pages: 34

FTK-MT12-NEO/GR

Brand: Funtek Pages: 22

Brand: Traction Hobby Pages: 20

Brand: Yokomo Pages: 32

Volkswagen TC Golf III GTI RAC RALLY '93 RED ARROWS

Brand: Fujimi Pages: 4

Brand: Fujimi Pages: 8

Brand: Fujimi Pages: 8

Brand: Jamara Pages: 8

Aston Martin Racing DBR9 Le Mans 2006

Brand: Kyosho Pages: 10

Brand: Tameo Kits Pages: 8

Brand: Traxxas Pages: 6

Brand: Tamiya Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands