When you enter this screen, press and to choose the right neutral pulse
position of the servo and enter to frequency setting.
Press and to choose the right frequency and enter swing/manual screen.
In this screen, press and to change the amplitude of the pulse width.
In this screen, press and to change the pulse width and
check the response of the servo to different pulse width.
ESC Settings
Li-Po Battery Analyzer
The Smartbox can check the total cell number, total voltage, each cell voltage, highest voltage and lowest
voltage and the voltage difference between the highest voltage and lowest voltage.
Servo Tester
The Smartbox can check the input voltage, servo travel position and peak current of your servo.
The default servo neutral position is 1520us/100Hz and 760us/100Hz. If the testing servo is not
1520us/100Hz and 760us/100Hz, please enter CUSTOM and set the servo neutral position (range: 200-
2000us) and frequency(range: 50-200Hz) by yourself.
There are two kinds of mode “Swing Mode” and “Manual Mode” to make the servo swing and check
the servo travel position.
Swing Mode:
The Smartbox will send out a signal to make the servo swing automatically
Manual Mode:
The Smartbox allows you to change the PPM signal and check the servo’s response to the
signal.
Input PPM Signal Monitor
The Smartbox can check the output voltage from the receiver, the receiver’s PPM signal / pulse width and
frequency.
Connect the Smartbox as
shown, turn on the ESC and
follow these steps.
Press button to enter
different programmable items,
press or buttons
to browse all the options and
press button to confi rm
your selection and then the
screen will go back to the main
program menu
Connect the Smartbox and the battery as shown, monitor battery voltage as follows
Connect the Smartbox with the receiver as shown, and
turn on the ESC and the transmitter. Please note that the
Smartbox must be inserted in the Throttle Channel and
a RX powerpack or the ESC can be inserted to any free
channel of the receiver to supply power to the receiver.
When all is connected, the Smartbox will display the output
voltage from the receiver, the receiver’s frequency and the
neutral pulse position.
Hold full throttle and hold full brake to check the receiver’s
PPM signal / pulse width.
Safety Notes
• This Smartbox is not a toy and only suitable for users from age 14+
• Never allow water, moisture, oil or other materials to get in contact or inside the Smartbox. It may damage
the Smartbox completely.
• Never disassamble the Smartbox or modify the components on the PC board
• We strongly suggest to use the original wires and connectors supplied in the ESC packaging
• To avoid short circuit, please keep the connectors away from any metal parts.
• Never connect a battery with reversed polarity.
Team Corally can never be held responsible for any damage caused or related to the
non-compliance with the above instructions.
Suitable for
Cerix Pro 120
Cerix Pro 120 1S
Cerix PRO 160
Revoc Pro 160
...
Input Voltage
6 - 10V DC
Input Current
500mA
Idle Current
< 20mA
Dimensions
85x55x13mm
Weight
46g
Technical Specifi cations
Connectivity
Features
• ESC Settings
• Servo Tester
• PC Interface - Link ESC to PC
• Motor KV/RPM Tester
• Input PPM Signal Monitor
• LiPo Battery Analyzer
Introduction
Setting up all parameters of your ESC made easy with this digital
programmer. The bright LCD screen let you run through all the
programs and within seconds the values have been changed. This
programmer can also be used as interface between your PC and
the ESC to update your fi rmware or to do even more set-ups.
The TC Smart Box offers six-in-one functions:
Functions
ESC Setting
The TC Smartbox can work as an individual device to program the ESC. The options of each parameter are
displayed on the LCD screen.
Servo Tester
The TC Smartbox can check the input voltage, servo travel position and peak current of your servo.
PC Interface
The TC Smartbox can work as an USB adaptor to link the ESC with your PC.
The user can update the fi rmware of the ESC or program the ESC by the TC CONNECT software on PC.
Motor KV/RPM Tester
The TC Smartbox can check the motor KV, RPM and input voltage.
Input PPM Signal Monitor
The TC Smartbox can check the output voltage from the receiver and the receiver’s PPM signal/pulse width
and frequency.
LiPo Battery Analyzer
The TC Smartbox can be used as a batterypack analyzer and tester to check the total cell number, total volt-
age, each cell voltage, highest voltage and lowest voltage and the voltage difference between the highest
voltage and lowest voltage.
INSTRUCTION MANUAL
TC SMART BOX
Application
There are 4 program buttons on the TC Smartbox
Press this button to ENTER into the referred menu or to CONFIRM your selection
Press this button to PAGE DOWN or SCROLL DOWN in the menu / selection
Press this button to PAGE UP or SCROLL UP in the menu / selection
Press this button to EXIT and go back to previous menu
Page 1
Page 2
Page 3
Page 4
Battery Balance
Connector
Motor Sensor
Connector
LCD Screen
2 Lines - 16 Characters
USB to PC
I/O Connector
ENTER
key
INC+
key (Up)
DEC-
key (Down)
EXIT
key (Esc)
ENTER
DEC-
DEC-
INC+
INC+
EXIT
ENTER
ENTER
EXIT
ENTER
ENTER
ENTER
When the screen displays the programed item, you can press the button to go back to the main
program menu and start to program next item.
Note: The programmable items in the menu may be differ between the different type of ESC’s
DEC-
DEC-
DEC-
DEC-
DEC-
DEC-
INC+
INC+
INC+
INC+
Connect RX Power
4.8 - 7.4V
or
ESC with battery
connected
ENTER
*Remark 1
*Remark 2
*Remark 3
ENTER
ENTER
ENTER
ENTER
ENTER
ENTER
INC+
INC+
INC+
DEC-
DEC-
DEC-
CORELESS - TITANIUM GEAR
HIGH VOLTAGE 6V - 8.4V
HIGH SPEED
