manualshive.com logo in svg

Team Blacksheep TBS UNIFY PRO32 5G8 nano, Manual

Share
Download
Team Blacksheep TBS UNIFY PRO32 5G8 nano Manual Download Page 17

 

 

 

 

 

 

CleanSwitch   

 

A   new   feature   introduced   with   the   TBS   UNIFY   PRO   5G8   is   CleanSwitch.   When   video   transmitters   power   up   

or   change   frequency,   they   usually   send   a   burst   across   the   entire   band   which   disturbs   fellow   flying   pilots.   

All   UNIFY   PRO32   5G8   video   transmitters   will   remain   in   their   lowest   power   output   (less   than   0.1mW)   while   

changing   channels   and   powering   up.   This   ensures   interruption-free   racing,   even   with   multiple   video   

transmitters   changing   channels,   or   powering   up.   Despite   all   this,   TBS   UNIFY   PRO   &   EVO   are   still   the   fastest   

video   transmitter   on   power   up   -   thus   ensuring   it   is   the   perfect   choice   for   any   application   where   quick   

channel   changes   are   a   necessity!   

 

Force   device   into   bootloader   mode   

 

In   some   rare   cases   it   can   be   required   to   force   the   device   into   bootloader   mode.   This   can   be   done   by   simply   

bridge   2   pads   on   the   unit   then   power   up.   For   regular   operation   this   will   not   be   required.    

  

Please   follow   the   diagram   below:     

   

●

TBS   Unify   Pro32   HV   (MMCX)   

 

 

 

●

TBS   Unify   Pro32   Nano   

 

 

 

 

 

17   

 

Summary of Contents for TBS UNIFY PRO32 5G8 nano




















Reviews:

No comments

Brands by name

Popular brands

Load more brands