Teac TN-4D-SE Owner'S Manual Download Page 2

2

IMPORTANT SAFETY INSTRUCTIONS

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO 
NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE 
PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE 
PERSONNEL.

M

The lightning flash with arrowhead in an equilat-
eral triangle is intended to alert the user to the 
presence of uninsulated “dangerous voltage” within 
the product’s enclosure that could be of sufficient 
magnitude to constitute a risk of electric shock to 
persons.

V

The exclamation point in an equilateral triangle 
is intended to alert the user to the presence of 
important operating and maintenance (servicing) 
instructions in the literature accompanying the 
appliance.

WARNING: TO PREVENT FIRE OR SHOCK 
HAZARD, DO NOT EXPOSE THIS APPLIANCE TO 
RAIN OR MOISTURE.

CAUTION

 

o

DO NOT REMOVE THE EXTERNAL CASES OR CABINETS TO 
EXPOSE THE ELECTRONICS. NO USER SERVICEABLE PARTS 
ARE INSIDE.

 

o

IF YOU ARE EXPERIENCING PROBLEMS WITH THIS PRODUCT, 
CONTACT THE STORE WHERE YOU PURCHASED THE UNIT 
FOR A SERVICE REFERRAL. DO NOT USE THE PRODUCT 
UNTIL IT HAS BEEN REPAIRED.

 

o

USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE 
OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN 
MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.

1)  Read these instructions.

2)  Keep these instructions.

3)  Heed all warnings.

4)  Follow all instructions.

5)  Do not use this apparatus near water.

6)  Clean only with dry cloth.

7)  Do not block any ventilation openings. Install in accordance 

with the manufacturer’s instructions.

8)  Do not install near any heat sources such as radiators, heat 

registers, stoves, or other apparatus (including amplifiers) 
that produce heat.

9)  Do not defeat the safety purpose of the polarized or 

grounding-type plug. A polarized plug has two blades with 
one wider than the other. A grounding type plug has two 
blades and a third grounding prong. The wide blade or 
the third prong are provided for your safety. If the provided 
plug does not fit into your outlet, consult an electrician for 
replacement of the obsolete outlet.

10)  Protect the power cord from being walked on or pinched 

particularly at plugs, convenience receptacles, and the 
point where they exit from the apparatus.

11)  Only use attachments/accessories specified by the 

manufacturer.

12)  Use only with the cart, stand, tripod, 

bracket, or table specified by the man-
ufacturer, or sold with the apparatus. 
When a cart is used, use caution when 
moving the cart/apparatus combina-
tion to avoid injury from tip-over.

13)  Unplug this apparatus during lightning storms or when 

unused for long periods of time.

14)  Refer all servicing to qualified service personnel. Servicing 

is required when the apparatus has been damaged in any 
way, such as power-supply cord or plug is damaged, liquid 
has been spilled or objects have fallen into the apparatus, 
the apparatus has been exposed to rain or moisture, does 
not operate normally, or has been dropped.

 

o

The apparatus draws nominal non-operating power 
from the AC outlet with its POWER or STANDBY/ON 
switch not in the ON position.

 

o

The mains plug is used as the disconnect device, the 
disconnect device shall remain readily operable.

 

o

Caution should be taken when using earphones or 
headphones with the product because excessive 
sound pressure (volume) from earphones or head-
phones can cause hearing loss.

CAUTION

 

o

Do not expose this apparatus to drips or splashes.

 

o

Do not place any objects filled with liquids, such as 
vases, on the apparatus.

 

o

Do not install this apparatus in a confined space such as 
a book case or similar unit.

 

o

The apparatus should be located close enough to the 
AC outlet so that you can easily reach the power cord 
plug at any time.

Company names and product names in this document are the 
trademarks or registered trademarks of their respective owners.

Summary of Contents for TN-4D-SE












Reviews: