manualshive.com logo in svg

Teac DV-B420, Owner'S Manual

Share
Download
Teac DV-B420 Owner'S Manual Download Page 18

- 35 -   

DV-B420                                                                                                                            Digital Terrestrial Receiver

- 34 -

DV-B420                                                                                                                            Digital Terrestrial Receiver

Technical Specifications

Tuner & Channel

Input Connector

:  IEC 169-2, Female

Frequency Range

:  174 MHz to 820 MHz

Signal Level

:  35dBuV to 70dBuV

Demodulation

:  COFDM 2K/8K-Carrier

Input Symbol Rate

:  24.1 Msymbol/s FEC Decoder

Convolutional Code Rate 3/4

MPEG Transport Stream A/V Decoding

Transport Stream

:  MPEG-2 ISO/IEC 13818

Transport stream Specification

Profile Level

:  MPEG-2 MP@ML

Input Rate 

:  Max 90 Mbit/s

Aspect Ratio 

:  4:3, 16:9

Video Resolution 

:  720 x 576

Audio Decoding 

:  MPEG / MusiCam Layer I & II

Audio Mode 

:  Single channel / Dual channel / Joint 

stereo

Sampling 

:  32, 44.1 and 48KHz

Main Resources

Main CPU 

:  ST20(STi5518)

Flash Memory 

:  1Mbyte

SDRAM for MPEG 

:  

SDRAM for SYSTEM

:           8Mbyte 

SDRAM for GRAPHIC

:

Power Supply

Input Voltage 

:  AC 100 ~ 230V 50/60Hz

Type 

:  SMPS 

Power Consumption 

:  15W MAX

Standby Power

:  Max. 4W

Protection 

:  Separate internal fuse.

T roubleshooting

Check the main power cord and check that it is 
plugged into a suitable power outlet. 

Check whether STB is in Standby mode.

Ensure that the STB is switched on (see above).

Check the video output port (VIDEO) is firmly
connected to the TV or VCR.

Check that you have selected the correct channel or
Video Input on your TV.

Check the brightness level of the TV.

See “No Picture” above.

Check the signal level, if this is low then try to

adjust the alignment of your antenna.

See “No Picture” above.

Check the volume level of the TV and STB.

Check the Mute status of the TV and STB.

Point Remote Control Unit directly towards the STB.

Check and replace batteries.

Disconnect STB from power point for 30 seconds 
and re-connect.

Adjust the direction of your antenna

Check the “Signal Strength” and the “Signal Quality” in
the channel list or channel search menu

Does not display any
message on the front panel 
or STB has no power.

No Picture

Breaking Picture

No Sound

Remote Control does not operate

STB is locked and doesn’t 
operate.

No or Bad Signal

Problem

Solution

Something wrong with STB

About On-Screen Error Message

More Information available at http://stb.teac.com.au

Summary of Contents for DV-B420






















Reviews:

No comments

Brands by name

Popular brands

Load more brands