manualshive.com logo in svg

TDK HAL 3900, User Manual

Share
Download
TDK HAL 3900 User Manual Download Page 12

 

 
TDK-Micronas GmbH 

 

Page

 12

 of 

23

 

Note

:   1. Do not solder a sensor at the face of the side PCB that is unused, if a sensor is already present, 

remove it. 

 

2. The Position of the HAL 3900 on the "2-pole 360 DEG" side of the side PCB is lower than the 
"4-pole 180 DEG" side. 

3.2.2.1  3Z rotational measurement 

1.  Fix the two 2-pole magnets at the sides of the joint (close to S3 and S4 connectors). 
2.  Solder the 2x4 Header at the edge of the two side PCBs 
3.  Solder the HAL 3900s on the two side PCB’s at the face indicating "4-pole 180 DEG". 
4.  Solder the Side PCBs to the Joystick PCB at S3 and S4 with the sensor facing the Joystick 

module. 

 

Figure 22: 2 pole magnets  

 

Figure 23: 3Z side PCB assembly ("4-pole 180 DEG" face) 

 

Figure 24: 3Z side PCB installation  

 

Figure 25: 3Z complete 

 

 

 

 

 

 

 

   

 

 

  11  

   12 

 

 

 

 

 

 

 

       

 

 

 

 

 

 

 

 

13   

 

 

14 

 

 

 

 

 

 

 

       

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

   

 

 

 

 

15 

 

 

16 

 

 

 

 

 

 

 

       

 

 

 

 

 

 

 

Summary of Contents for HAL 3900
























Reviews:

No comments

Brands by name

Popular brands

Load more brands