background image

TDI

 T

URBO

T

WIN

 

FROM 

TECH DEVELOPMENT

 

 

 

                                                                                                                   

                           

Publication:   T1-795 

                                                                                                  Issued: August 1, 2008

                             

                                                                                                                                                                                                

Page 10 

6.0 WARRANTY 

 

TDI TURBOTWIN ENGINE MOTOR WARRANTY

 

Tech Development (TDI) warrants to the original user of the TDI 

TURBO

TWIN

™ air starters to be free from defects in material 

and workmanship for a period of one year (6 month for remanufactured units) from the date of installation.  The warranty period 
shall not extend beyond two years (12 months for factory remanufactured units) from the date the unit was manufactured. (i.e.: a 
unit with a manufactured date of July 1999 (SN: 9907-101) will not be covered under warranty after July 2001).   The conditions 
of this warranty are: 

a)

 TDI is notified within this period by return of such product to TDI or its authorized distributor/dealer, 

transportation prepaid by user; 

b)

 the starter has been installed according to TDI’s specifications; 

c) 

the starter has not been 

misused, abused, or improperly maintained by user; 

d)

 the defect is not the result of normal wear and tear; 

e)

 the starter has  

been repaired with parts manufactured or authorized by TDI; and 

f

) TDI installation and repair procedures as outlined in the 

appropriate manual were properly followed. 
 
Tech Development will repair, or at its option, replace the unit during the warranty period at no charge to the customer, 
provided it is returned to TDI with the proper return procedure. 

 
Tech Development makes no other warranty, and implied warranties including any warranty or merchantability or fitness for a 
particular purpose are hereby disclaimed. 
 
This warranty constitutes the entire obligation of Tech Development relating to the sale and use of such product and TDI’s 
maximum liability is limited to the purchase price of such product at the date of purchase.  In no event shall TDI be liable for 
incidental, indirect, consequential, or special damages of any nature arising from the sale or use of such engine starter 
product. 

Summary of Contents for TURBOTWIN T100-MS












Reviews: