manualshive.com logo in svg

TCS QWL2040, Installation Manual, Page: 12 / 45

Share
Download
TCS QWL2040 Installation Manual Download Page 12

12

13

2800 Laura Lane • Middleton, WI 53562  

|

  800.288.9383  

|

  www.tcsbasys.com  

Building Automation Systems

12

13

Installation

QWL2040 Panel at end of the 

network.

QWL2040 Panel in middle of the 

network.

1

3

2

Shielded, twisted two-conductor 

communications wiring with one end 

earth grounded. (120 Ω balancing 

resistors provided.)

Shielded, twisted two-conductor 

communications wiring with one end 

earth grounded. (120 

Ω

 balancing 

resistors provided.)

4

NOTES:

1.  If using more than 64 

controllers, use the second 

RS485 port or additional QD1010 

adapters. 

2.  Each controller must use the 

same baud rate and be assigned 

a unique address. 

Two-Wire Network Wiring

Follow this wiring diagram for two-wire (Modbus) wiring systems (this is not common).

Two-wire diagram 

A

B

Shield

A

B

A

B

Earth Ground

Only at one end

Drain

Wire

Last in Daisy Chain

120Ω  

Terminating

Resistor

COM 1

REF

A

B

Drain

Wire

120Ω  

Terminating

Resistor

A
B

A
B

A
B

Last in Daisy Chain

Shield

Last in Daisy Chain

Earth Ground

Only at one end

120Ω  

Terminating

Resistor

A
B

A
B

A
B

Shield

Drain

Wire

COM 1

REF

REF

A

A

B

B

120Ω  

Terminating

Resistor

1

2

3

3

4

4

4

COM 1

REF

A

B

COM 1

REF

A

B

Summary of Contents for QWL2040














































Reviews:

No comments