TC Communications TC1710 User Manual Download Page 19

TC1710  RS-485

  (Optional  Dual  Optics)

User's  Manual

Rev.  1.6

−19−

Appendix C

Return Policy

To return a product, you must first obtain a Return Material Authorization number from the Customer

Service Department.  If the product’s warranty has expired, you will need to provide a purchase order to

authorize the repair.  When returning a product for a suspected failure, please provide a description of  the

problem and any results of diagnostic tests that have been conducted.

Warranty

Damages  by  lightning  or  power  surges  are  not  covered  under  this  warranty.

All products manufactured by TC Communications, Inc. come with a five year (beginning 1-1-02)

warranty.  TC Communications, Inc. warrants to the Buyer that all goods sold will perform in accordance

with the applicable data sheets, drawings or written specifications.  It also warrants that, at the time of sale,

the goods will be free from defects in material or workmanship.  This warranty shall apply for a period of

five years from the date of shipment, unless goods have been subject to misuse, neglect, altered or destroyed

serial number labels, accidents (damages caused in whole or in part to accident, lightning, power surge, floods,

fires, earthquakes, natural disasters, or Acts of God.), improper installation or maintenance, or alteration or

repair by anyone other than Seller or its authorized representative.

Buyer should notify TC Communications, Inc. promptly in writing of any claim based upon warranty, and

TC Communications, Inc., at its option, may first inspect such goods at the premises of the Buyer, or may

give written authorization to Buyer to return the goods to TC Communications, Inc., transportation charges

prepaid, for examination by TC Communications, Inc. Buyer shall bear the risk of loss until all goods

authorized to be returned are delivered to TC Communications, Inc. TC Communications, Inc. shall not be

liable for any inspection, packing or labor costs in connection with the return of goods.

In the event that TC Communications, Inc. breaches its obligation of warranty, the sole and exclusive

remedy of the Buyer is limited to replacement, repair or credit of the purchase price, at TC Communications,

Inc.’s option.

To return a product, you must first obtain a Return Material Authorization (RMA) number and RMA form

from the Customer Service Department.  If the product’s warranty has expired, you will need to provide a

purchase order to authorize the repair.  When returning a product for a suspected failure, please fill out RMA

form provided with a  description of the problem(s) and any results of diagnostic tests that have been

conducted.  The shipping expense to TC Communications should be prepaid.  The product should be properly

packaged and  insured.  After the product is repaired, TC Communications will ship the product back to the

shipper at TC's cost to U.S. domestic destinations. (Foreign customers are responsible for all shipping costs,

duties and taxes [both ways]. We will reject any packages with airway bill indicating TC communications

is responsible for Duties and Taxes. To avoid Customs Duties and Taxes, please include proper documents

indicating the product(s) are returned for repair/retest).

Limitation of Liability

1. In no event shall the total liablility of TC Communications, Inc. to purchaser and/or end user for all

damages including but not limited to compensatory, consequential and punitive damages, exceed the total

amount paid to TC Communications, Inc. by purchaser for the goods from which the claim arose, in no event

shall TC Communications, Inc. be responsible for indirect and consequential damages.

Continue  on  next  page.

Summary of Contents for TC1710





















Reviews: