TBB idSWITCH LMP1218-PWM User Manual Download Page 16 | Manualshive

Page: 16 / 21

TBB idSWITCH LMP1218-PWM User Manual Download Page 16

LMP1218-PWM Master Power Unit User Manual

IDM Technologie

12

5.

OPERATION

5.1

Configuration on LMP1218-PWM

You could set the battery type, VCR and Mode through LMP1218-PWM master power unit.

5.1.1

Dip switch setting

There are dip switches for you to set VCR mode, Working mode and Battery type.

Figure 6 Dip switch

Table 5 Dip switch definition

5.1.1.1

Dip switch for VCR mode and Working mode

Table 6 Dip switch for VCR mode and Working mode selection

a) VCR mode

There are two VCR modes for optional:
- Integrated VCR: when this mode is selected, the integrated VCR is activated, i.e. 18A
- Ex-DC / DC: When this mode is selected, the integrated VCR is deactivated; and an IDM NEMO
type external DC-DC booster can be connected to replace this integrated VCR

Caution

If Booster set the VCR to ON and only for LEP lithium batteries

b) Working mode

There are two working modes for optional:

DIP SWITCH

1

2

3

4

VCR mode

Working mode

Battery type

VCR mode

off Built-in VCR (Default setting)

on

Ex-DC/DC

Working mode

off Charger (Default setting)

on

Power supply

«
...
14
15
16
17
18
...
»

Summary of Contents for idSWITCH LMP1218-PWM






















Reviews:

No comments