THIS BOX CONTAINS:
3 - Center Bows (slightly curved bows)
2 - "A" Bow Assembly (longest bow)
2 - "C" Bow Assembly (shortest bow)
2 - "B" Bow Assembly
1 - Bimini Canvas Assembly
1 - Bimini Top Boot (optional with marine vinyl tops)
2 - Adjustable Bow Straps (loop on each end)
4 - Adjustable Tie Down Straps (loop on one end, snap on other)
1 - Hardware Bag Assembly containing:
PART 1: ASSEMBLING THE FRAME
Step 1
"A" bow to "C" bow assembly:
a) Slide (1) jaw slide over the end of one "A" bow with tie-down strap hole facing upward and slide it
approximately half of the way to the bend. DO NOT tighten the set screw yet!
b) With the "A" bow laying flat, as shown below, orient the jaw slide facing upward.
c) Connect a "C" bow to the jaw slide, placing the eye end from the "C" bow into the jaw slide then
reinserting the screw into the jaw slide. Secure the screw but do not over tighten.
d) Align the bend in the "C" bow with the bend in the "A" bow and secure the jaw slide by tightening
the set screw on the back of the jaw slide.
e) Slide another jaw slide onto the "A" bow, orient the jaw
slide facing upward (same as for "C" bow) and secure
it approximately 2" from the end of the "A"bow.
f) Repeat the previous actions a) - e) for the other "A"
and "C" bow. Remember to have the bend facing
in the opposite direction as the bows
you just assembled. (If the first set you
assembled had the bend facing left,
assemble the second pair of
bows facing right.)
WAKE BOARD TOWER BIMINI TOP ASSEMBLY INSTRUCTIONS
Tools Required:
• #2 Phillips head screwdriver
• Flat head screwdriver.
• Drill with 1/8" drill bit
Snap Button
Jaw Slide
HARDWARE BAG ASSEMBLY CONTAINS:
12 - 5/8" phillips head stainless steel screws
4 - 3/4" phillips head self tapping stainless
steel screws.
4 - Eye Straps (black)
2 - Vertical Deck Mounts
4 - 7/8" Jaw Slides
6 - Snap buttons
4- Cup washers
Eye Strap
Vertical Deck Mount
These Bimini Tops are designed to mount within the confines of most wake board towers to provide
shade for driver and spotter. All tops are 48" long and approximately 16" (from mounting point) and are
available in three different widths to best fit most towers.
Choosing the correct size top:
The tops will mount directly onto the tower frame at the center point, so pick the best position on the
tower that will provide the best shade to the driver’s seat. The tops are low profile at approximately 16”
high at the maximum, so be sure that the position will keep the top high enough to clear the driver and
spotter when seated. Measure across the tower at the mounting point that you have selected. Choose
the dimensions from the chart below, noting the bimini width that matches your measured width on the
tower. Check the width at the top and be sure that the angle of your tower
will accommodate that dimension.
If your mounting point does not fall
into the dimensions below, or your
tower doesn't have the upward clear-
ance, this top will not fit properly on
your boat. Repack all components and
return the top to the place of purchase.
Once you have determined that the top is correct for your application, you may begin assembly and
mounting. You will need full access in and around the boat and tower for initial installation. It can be
done with the boat in the water, with care and best with a helper.
Width at Mount Width at top
68"-71" 60"
75"-78" 67"
81"-84" 73"
Width at top
Measure up 16"
Mounting point width
▲
▲
▲
▲
▲
C -Bows
A-Bow Left
Jaw slide for B-Bow attachment
Jaw slide faces upwards
approx. 2" from end
Position C-Bow
in alignment with
A-Bow and secure
jaw slide
B-Bow Left
Strap hole facing upward
Strap hole
facing downward
