manualshive.com logo in svg

Taylor-Dunn B 2-10, Operation, T Roubleshooting And Replacement Parts Manual

The Taylor-Dunn B 2-10 is a versatile, electric utility vehicle designed for various operational tasks. To ensure smooth operation, quick troubleshooting, and easy maintenance, it is crucial to have an "Operation, Troubleshooting, and Replacement Parts Manual." Download this essential manual for free from manualshive.com to maximize the potential of your Taylor-Dunn B 2-10.

Share
Download
background image

Maintenance, Service, and Repair

Steering

Page 13

REPAIR THE STEERING GEAR

Disassembly

NOTE: The steering gear must be removed from the vehicle for this procedure. Refer to 

Replace the

Steering Gear 

section for information regarding removing the steering gear.

NOTE: The steering gear is packed with grease. Only perform maintenance on the steering gear in an

area that will contain any grease that may spill out of the steering gear when it is disassembled.

Refer to the illustration at the end of this section for a blown up view of the steering gear assembly.

1. Center the steering gear.

A. Turn the steering shaft all of the way in one

direction.

B. While counting the rotation, turn the steering

shaft all of the way in the opposite direction.

C. Turn the steering shaft 1/2 the number of turns

in the original direction.

2. Remove the worm bearing adjuster locking ring

and the worm bearing adjuster.

3. Remove the side cover/pitman shaft assembly by

removing  the three side cover bolts and then

pulling the assembly out of the housing.

NOTE: The side cover/pitman shaft assembly

normally does not have to be disassembled.

4. Remove  the worm shaft and ball nut assembly

from the bottom of the housing.

5. Remove the worm shaft seal.
6. Remove the pitman shaft seal.
7. Remove the upper worm bearing and bearing cup

from the housing.

8. The ball nut assembly consists of two sets of ball

bearings  that recirculate in two channels in the

ball nut housing. The bearings may fall out once

the bearing guides are removed. Be careful not to

lose any of the bearings.

9. Remove the ball guide clamps, ball guides and all

of the ball bearings.

10. Remove the ball nut from the worm shaft.
11. Thoroughly clean and inspect all parts for signs of

corrosion,  damage or wear and replace as

required.

Summary of Contents for B 2-10































































































































































































































































Reviews:

No comments

Related manuals for B 2-10

E-TON 2006 Viper 70 Owner'S Manual preview
2006 Viper 70
Brand: E-TON Pages: 36
Arctic Cat M6000 Operator'S Manual preview
M6000
Brand: Arctic Cat Pages: 64
Yamaha 2002 YFS200 Supplementary Service Manual preview
2002 YFS200
Brand: Yamaha Pages: 25
Yamaha 2002 YFM400FWA Service Manual preview
2002 YFM400FWA
Brand: Yamaha Pages: 41
Yamaha 50 Owner'S Manual preview
50
Brand: Yamaha Pages: 134
Yamaha 4x4 Timberwolf YFB250FWM Owner'S Manual preview
4x4 Timberwolf YFB250FWM
Brand: Yamaha Pages: 161
Yamaha 1982 SRX600C Owner'S Manual preview
1982 SRX600C
Brand: Yamaha Pages: 81
Yamaha 4X4 BIG BEAR YFM40FC Owner'S Manual preview
4X4 BIG BEAR YFM40FC
Brand: Yamaha Pages: 168
Yamaha 4X4 BIG BEAR PROFESSIONAL Owner'S Manual preview
4X4 BIG BEAR PROFESSIONAL
Brand: Yamaha Pages: 172
Yamaha 2006 GRIZZLY 125 Owner'S Manual preview
2006 GRIZZLY 125
Brand: Yamaha Pages: 153
Yamaha 2012 Griizzly 700 YFM7FGPB Owner'S Manual preview
2012 Griizzly 700 YFM7FGPB
Brand: Yamaha Pages: 174
Yamaha 2004 Rhino 660 YXR660FAS Owner'S Manual preview
2004 Rhino 660 YXR660FAS
Brand: Yamaha Pages: 154
Yamaha 1998 BigBear 2x4 YFM350UK Owner'S Manual preview
1998 BigBear 2x4 YFM350UK
Brand: Yamaha Pages: 168
Yamaha 2009 Raptor 250 Service Manual preview
2009 Raptor 250
Brand: Yamaha Pages: 293
Yamaha 2008 Raptor 250 Service Manual preview
2008 Raptor 250
Brand: Yamaha Pages: 311
Yamaha 4SH-28199-67 Owner'S Manual preview
4SH-28199-67
Brand: Yamaha Pages: 382
Yamaha 2003 YFZ450S Service Manual preview
2003 YFZ450S
Brand: Yamaha Pages: 375
Yamaha 2004 Rhino 660 YXR660FAS Service Manual preview
2004 Rhino 660 YXR660FAS
Brand: Yamaha Pages: 421

Brands by name

Popular brands

Load more brands