manualshive.com logo in svg

Tatung TME24, User Manual, Page: 6 / 20

Share
Download
Tatung TME24 User Manual Download Page 6

5

3. Fasten the wall mounting stand at the position of VESA on the rear cover with bolts. 
4. Spin M4 bolts into the left-right nuts on the wall mounting stand. 3-4 mm of depth from bolts washer to stand is recommended.
5. Hang the machine onto the slot of the wall mounting board. Then lock the two bolts on the sides.

Note

: 

●

 Installation method is different because of Hanging arm hardware's 

.

          

●

 

          

●

 

structure

Must install the wall pendant on firm wall surface, please do not install this machine on ceiling or vehicles.
Wall-mounting parts are not included in accessories and have to be purchased by the client if needed.

Tips on Installation:

● The 

 set should be mounted near the AC power socket for easy plugging and unplugging.

Monitor

10cm

10cm

10cm

7cm

30cm

Mount on the wall

Mount on the base

Obstruct the air circulation

●

 

, 

     

●

 

●

Please keep this space at least around the 

as 

shown in the figure.

Do not cover the air vents or insert any object into 

     the enclosure.

 Do not put the device in limited space, e.g. Bookcase

     or embedded closet, unless the 

 set is properly 

     ventilated.

Monitor

Monitor

Ventilation

Obstruct the air circulation

Wall

Wall

10cm

30cm

10cm

Summary of Contents for TME24





















Reviews:

No comments