background image

70

Marchesan Implementos e Máquinas Agrícolas “TATU” S.A.

GAPCR-HD 8013/GASPCR-HD 9017/GASPCR-EHD 10020

Maintenance

Wheelset hubs lubrication

The wheelset hubs must be lubricated every 150 hours. When the existence of any 

clearance is noticed, carry out a maintenance on the wheel hubs.

Disassemble the hubs and remove their internal components. Clean all parts using 

diesel oil or kerosene.

Check the existence of clearances, the condition of the bearings, retainers or bushings. 

If there is any part that shows excessive wear or damages, replace them.

The bearing must be replaced in a preventive manner, to avoid that it breaks and to 

avoid greater maintenance costs, since more parts of the set suffer damages when the 

bearing breaks during the job.

• For models with 400/60 x 15.5 tires - 14 ply

Check the retainer position (A) to let the excess of grease flow out of the hub and be 

careful to not damage the retainer.

Adjust the flat washer (B) and the castle nut (C) on the hub using a wrench to get 

some resistance while turning the hub. Do not totally tighten it. Lock it using a cotter pin (D).

Place the hubcap (E) and lock using a bolt (F) and spring washer. Lastly, attach the 

grease fitting (G) on the hubcap.

A

A

D

D

B

B

C

C

E

E

F

F

G

G

Summary of Contents for 05.03.03.3933





















































































Reviews: