19
I2
5
I2
4
I2
3
I2
2
I2
1
I2
0
I1
9
I1
8
I1
7
I1
6
I1
5
I1
4
I1
3
tr
s
l
p
t
p
l
n
l
jp
it
fr
e
n
d
e
d
a
c
z
Preparation for operation/Operation
Preparing the carpet
Filling the tank
Only use chemical products recommended by the manufacturer.
The correct dosage is recommended on the product's packaging and on the "
TASKI Product Information Sheet".
Dosage:
The "Max". mark on the dosing aid shows the maximum solution filling level (
refer to Page 18).
Dosing examples (The concentration is product dependent)
Volume of moisture in the foam is measured as a percentage.
• The position of the dosing control unit defines the amount of moisture within
the foam, which affects the drying time of the carpet.
Application technique
Cleaning methods are described in detail in the the "Method Card" which you
can obtain from your TASKI partner.
Beginning work
Refilling the foam solution
Stair transportation
Vacuum off the carpet before working with the carpet-cleaning
machine.
In the case of visible stains, treat the carpet with a TASKI stain
remover. Your TASKI partner can help you with this.
Caution:
Using other chemicals (e.g. chemicals containing solvents,
chlorine, hydrochloric acid and hydrofluoric acid) can damage or
destroy the machine.
Maximum permissible water temperature 30 °C/86 °F.
• Screw off the tank lid.
• Add the product measured in the dosing cup to the water in the clean
bucket.
Instructions on the product’s
packaging
Tank
capacity
The volume per tank
filling
3%
300ml auf 10l
Wasser
10l
300ml = 0,3l
10%
1000ml auf 10l
Wasser
10l
1000ml = 1,0l
• Fill the prepared foam solution in the tank and
screw on the tank lid.
• Loosen the adjusting lever and raise the
operating handle until you can work with it
comfortably (working position).
Lock the adjustment lever again.
• Switch the machine on (Main switch and mains
socket).
The main switch lights up.
• Press the foam generator switch.
The main switch lights up.
• Choose the amount of foam solution with the
dosing control unit (min.1 /max.4).
Wait for the foam to be applied to the brush.
1
2
0
4
3
2
1
• Tip the machine lightly backwards and lower the
cylinder brushes by pressing the foot pedal.
With the rotary button, you can adjust the height
of the cylinder brushes to the floor level of the
carpet.
• Pull the machine drive bow to the machine
handle.
The tools thereby start to turn, and the foam
solution is output in the centre of the tools.
The freshly shampooed carpet may not be walked on with outdoor
shoes or shoes with leather soles.
• After shampooing, use a web-brush to raise the carpet pile into place.
Allow enough time for the carpet to dry.
• After the drying period, vacuum up the crystalline dirt with a brush vacuum
cleaner.
Caution:
The hose that is connected with the quick coupler must not be
removed while under pressure (for accessories)!
First slowly open the tank lid to relieve the pressure.
Caution:
Never work without foam solution, as this could damage the floor
covering.
Briefly interrupt the carpet cleaning,release the switch lever on
the left or the right.
The cylinder brushes then switch off so that there will be no
damage top the carpet.
• Stop cleaning.
• Refill the machine as described (Page 19).
Caution:
The tank must be emptied before transporting over stairs!
We recommend the transporting of the machine up or down steps
to be performed by two people.
Caution:
Due to the weight of the machine, there are risks involved in such
transportation!
Accidents could result in injury to an individual or damage to the
machine.
• To lift the machine, one person must hold the
tool unit and the other person must hold the
machine handle.
To Order Parts Call 1-888-702-5326 - https://monsterfloorequipmentparts.com
