background image

 

WARNING: 

This warning symbol identifies specific instructions or procedures which if 

                     not correctly followed could result in personal injury or death.

 

CAUTION: 

This caution symbol identifies specific instructions or procedures which, if 

                    not strictly observed, could result in damage to, or destruction of equipment 
                    and/or property.

 

WARNING: 

When using this product basic precautions should always be followed,

                     including the following:

SAFETY INFORMATION

3

Please read and understand this entire manual before attempting to assemble, operate or install 
the product. If you have any questions regarding the product, please contact our customer service 
department at 1-866-788-5598.

Safety precautions are essential when any mechanical equipment is involved.  These 
precautions are necessary when using, storing, and servicing mechanical equipment.  Using this 
equipment with the respect and caution demanded will considerably lessen the possibilities of 
personal injury.  If safety precautions are overlooked or ignored, personal injury or property 
damage may occur.  The following symbols shown below are used extensively throughout this 
manual.  Always heed these precautions, as they are essential when using any mechanical 
equipment.

1. Read all the instructions before using the product.
2. To reduce the risk of injury, do not operate near children or animals.
3. Know how to stop the product and bleed pressures quickly. Be thoroughly familiar with the 
controls.
4. Stay alert - watch what you are doing.
5. Do not operate the product when fatigued or under the influence of alcohol or drugs.
6. Keep operating area clear of all persons.
7. Do not overreach or stand on an unstable surface. Keep good footing and balance at all times.
8. Follow the maintenance instructions specified in the manual.
9. This product is provided with a Ground Fault Circuit Interrupter built into the power cord plug. 
If replacement of the plug or cord is needed, use only identical replacement parts.
10. Do not touch plug or outlet with wet hands.
11. Avoid accidental starts. Move switch on unit to “OFF” position before connecting or 
disconnecting cord to electrical outlets.
12. Water spray must never be directed towards any electric wiring or directly towards the 
pressure washer machine itself or fatal electric shock may occur.
13. Never carry your pressure washer by the cord. Do not pull on the cord to disconnect from 
the outlet.
14. To prevent damage, the cord should not be crushed, placed next to sharp objects or near a 
heat source.

This unit was designed for specific applications. It should not be modified and/or used for any 
application other than that which it was designed.

Summary of Contents for TF2000



















Reviews: