background image

©Copyright Task Force Tips LLC 2002-2020

3

LIN-040 November 30, 2020 Rev15

1.0 MEANING OF SAFETY SIGNAL WORDS

A safety related message is identified by a safety alert symbol and a signal word to indicate the level of risk involved with a particular

hazard. Per ANSI Z535.6, the definitions of the four signal words are as follows:

2.0 SAFETY 

                                                                                                                                               

DANGER

DANGER indicates a hazardous situation which, if not avoided, will result in death or serious injury.

WARNING

WARNING indicates a hazardous situation which, if not avoided, could result in death or serious 

injury.

CAUTION

CAUTION indicates a potentially hazardous situation which, if not avoided, could result in minor

or moderate injury.

NOTICE

NOTICE is used to address practices not related to physical injury.

DANGER

An inadequate supply of pressure and/or flow will cause an ineffective stream and can result

in injury or death. Choose operating conditions to deliver adequate fire suppression. See flow

graphs. 

WARNING

This equipment is intended for use by trained personnel for firefighting. Use of this equipment for

other purposes may involve hazards not addressed by this manual. Seek appropriate guidance and 

training to reduce risk of injury. 

WARNING

Equipment may be damaged if frozen while containing significant amounts of water. Such damage 

may be difficult to detect visually. Subsequent pressurization can lead to injury or death. Any time 

the equipment is subject to possible damage due to freezing, it must be tested and approved for 

use by qualified personnel before being considered safe for use. 

WARNING

Failure to restrain nozzle reaction can cause injury from loss of footing and/or stream protection. 

Opening and closing other nozzles, hose line kinks, changes in pump settings, nozzle pattern, or 

flushing will cause changes in nozzle reaction. Nozzle operator must always be prepared in the 

event of these changes. 

WARNING

If nozzle gets out of control while flowing, violent whipping motion will occur. Serious injury or 

death could result. Retreat from the nozzle immediately. Do not attempt to regain control of nozzle 

while flowing. 

WARNING

Application of water or foam solutions on energized electrical equipment could cause 

electrocution. Serious injury or death could result. Assume circuits are energized until confirmed to 

be de-energized. Do not apply water or foam to energized electrical equipment. 

WARNING

The stream exiting a nozzle is powerful and capable of causing injury and property damage. Make 

sure the nozzle is securely attached and pointing in a safe direction before water is turned on. Do 

not direct water stream to cause injury or damage to persons or property. 

NOTICE

To prevent mechanical damage, do not drop or throw equipment. 

Summary of Contents for METRO 0 Series

















Reviews: