1- Introduction
1
TASCAM CC-222SL
2 – Features of the CC-222SL
k
Disc slot
Insert a disc into the slot with the label side
uppermost. When the
Eject
key is pressed, the loaded
disc is ejected from the slot.
l
MULTI DIAL
Used to select and confirm menu settings
etc. (turn to make the setting, push to confirm), and also
as a track search key when playing back discs.
;
REMOTE SENSOR window
Receives the infrared
signals from the remote control unit. Do not block this
window if you are using the remote control unit.
z
PITCH CONTROL knob
This is a centerdetented knob
which allows the tape speed (and therefore the pitch) to
be changed by ±10%.
x
REV MODE switch
This three-position switch allows
the choice of single-side (
Ä
) or bidirectional (
Ê
)
playback and recording, or continuous (
ä
) playback
only (not recording).
c
DOLBY NR (OFF/ON) switch
Use this switch to turn the
Dolby noise reduction on and off for the cassette deck.
v
CD-TAPE CONT PLAY key
Use this to turn continuous
playback (alternating between disc and cassette) on and off.
b
CD TIMER (OFF/PLAY) switch
Use this switch to turn
the CD timer option on or off. When this is in the
PLAY
position, turning on the machine with a disc inserted
will automatically start playback.
n
CD STOP key
Stops CD playback or disc recording.
m
CD PLAY key
Starts CD playback or recording (from
record standby mode).
,
CD PAUSE key
Pauses or resumes CD playback or
recording (starts recording from record standby mode).
.
CD RECORD key
Places the disc in record standby
mode and performs manual track incrementing while
recording.
/
MONITOR (TAPE,MIX,DISC) switch
This switch
selects the source for the headphone outputs as either the
cassette deck, the disc recorder, or a mixture of both.
!
PHONES jack and volume control
Connect a standard
pair of stereo headphones to this 1/4” jack, and adjust
the level with the control.
Rear panel
@
#
&
$
%
^
@
DIGITAL COA XIAL (INPUT and OUTPUT) jacks
These RCA jacks input and output SPDIF digital audio
data to and from the disc recorder.
Digital audio data received can be at any sampling
frequency between 32kHz and 48kHz. The output is
always 44.1kHz.
#
DIGITAL OPTICAL (INPUT and OUTPUT) jacks
These
TOSLINK-compatible connectors input and output
SPDIF digital audio data to and from the disc recorder.
Digital audio data received can be at any sampling fre-
quency between 32kHz and 48kHz.
$
LINE OUTPUTS (L,R) / 1(CD), 2(TAPE/AUTO)
Use
these connectors to connect the amplifier to the analog
outputs of the disc recorder (1) or the outputs of the cas-
sette deck (2).
%
RIA A PHONO INPUT (L , R) and GND terminal
Use these connectors to connect a record deck to the
CC-222SL. The destination of the signal is determined
by a menu item.
Connect the earth (grounding) wire of the record deck
to the
GND
terminal.
NOTE
Do not connect a record deck to the
LINE
inputs and
do not connect any other equipment to these jacks.
^
LINE INPUTS (L,R) / 1(CD), 2(TAPE)
Use these con-
nectors to connect signal sources to the analog inputs
of the disc recorder (1) or the inputs of the cassette deck
(2).
&
AC IN jacks
Connects the power cable supplied.
*
VOLTAGE SELECTOR switch
Switches the voltage to
either
230 V
or
120 V
.
NOTE
The voltage selector is only available on units for North
American market.
