background image

 

Maintenance 

Very little maintenance is required for your Tarheel Antenna. You should have years of 
trouble  free  service  from  this  antenna.  You've  made  a  large  investment  for  a  mobile 

antenna. Here is a tip to help take care of your investment. 
We  use  an  automotive  finish  on  this  antenna  so  whenever  you  wash  and  wax  your 

vehicle raise your antenna and wash and wax the shaft and the bug shield (Lexan tube), 
with wax on your antenna the bugs will have a harder time sticking to it. 

About once per year or so, depending on how much driving you do and where the antenna is 
mounted you will need to wash the coil to remove any road grime, no parts to replace. Also a 
dirty coil will show vertical black streaks.  

Here's how to clean the coil: 
1.  Run the antenna up till all the coil is exposed.  
2.  Remove the are 3 screws in the top Delrin Cap. 
3.  Then slide the Lexan bug shield down to expose the coil, next feel the coil, is it sticky?  
4.  If so it's dirty, now wipe the coil with alcohol.  
5.  Then lightly scrub the coil with a Scotch-Brite pad (available at any hardware store). 
6.  Then one more wipe with alcohol and that's it. 
7.  Reassemble the Antenna. 

After you have the antenna reassembled, now is the time for a good cleaning on the outside. 
Use the alcohol to remove the grime off the tube and Lexan, next get a good coat or two of 
wax on it. 

Warranty & Guarantee 

IF for the 1st 30 days if for any reason you are not completely satisfied, return the 

antenna undamaged for a full refund less the shipping charges. The antenna has a 
ONE YEAR NO MATTER WHAT WARRANTY

 

to the original owner

If for any reason 

(

other than damage due to unauthorized disassembly, negligence, improper 

use, or use of Non-recommended Controllers

) your Tarheel Antenna fails to 

perform due to quality or workmanship Tarheel Antennas, Inc. will at our discretion 

either repair or replace at no charge for parts or labor.

 

Shipping charges are your 

(the customer's) responsibility to and from Tarheel Antennas' repair shop. 

We here 

at Tarheel Antennas hope you enjoy one of the best performing, best built, best  looking 
motorized antennas available. 

We here at Tarheel Antennas hope you enjoy one of the best performing, best built, 
best looking motorized antennas available. 
Please  pass  along  any  suggestions  you  may  have  to  make  our  antenna  better. 
All  suggestions  are  appreciated.  Also  when  you  have  your  antenna  installed  please 

send us

 

pictures.

 

Thanks,  
Tarheel Antennas 

 

Summary of Contents for 400A










Reviews: