background image

WARNING 

Serious or  fatal crushing  injuries can occur 
from  furniture  tip-over.  To help  prevent 
tip-over: 

• Install  tip-over  restraint  provided. 

• Place  heaviest  items  in  the lowest drawers. 

• Do  not  set TV's or other heavy  objects  on  top 

of this product, unless the  product is 
specifically designed to accommodate them. 

• Never allow children  to climb  or  hang  on  drawers, 

doors,  or shelves. 

•Never open more  than  one  drawer at a time. 

(OR) 

•Do not defeat or  remove  the drawer interlock 

system. 

Use of  tip-over restraints may  only reduce, 
but  not  eliminate,  the  risk of tip-over. 

This is  a permanent label.  Do  not remove. 

1. This unit has been designed for the weight shown. Exceeding this recommended weight could result in 

excessive “sagging” of the top. Extreme overloading can cause failure of the top and possible injury. 

2. Furniture Care Instructions: Dust with a clean, lint-free cloth. Use a spray furniture polish as needed.

19

QUESTIONS? 

Just call 855-MYTGTHOME (855-698-4846) for parts and service. For faster service, have the style number and DPCI number ready when calling.

80 lbs.

15 lbs.

Summary of Contents for Windham WNCBDW2DBK





















Reviews: