background image

 

18

 

DRL

-

048, DRL

-

072 Crop Seeder

 

Operating Instructions

 

 

Seed cup shutoff:

 

 

Depending on the crop being planted, it may be necessary to not disburse from all of the seed cups. This is eas-
ily done by simply sliding the 

Seed shut off flap

” 

in and out.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Closed

 

The depth in which the application is done is controlled by adjust-
ing the basket located near of the machine. Adjusting the 

Sowing 

depth control device 

“ 

as follows:

 

 

Turning knob clockwise will make the basket drop which in turn 
will raise the disc openers and lessen the depth of the application. 
Turning the knob counterclockwise would raise the basket which 
would lower the disc openers and make the application deeper.

 

 

The top link on the tractor should be properly adjusted to carry the 
machine level in an operating position. During operation, the tractor 
lift must be fully lowered to allow the machine to follow the con-
tour of the ground.

 

 

The machine is totally ground driven so proceed with a speed that 
is most comfortable and safe for existing conditions. Be sure to stop 
forward motion before lifting machine off ground. This practice 
will stop rollers from 

free spinning

” 

and therefore eliminate the 

unwanted application when turning around.

 

 

Never operate the machine in reverse.

 

 

 

 

Open

 

Closed

 

Open

 

Closed

 

Open

 

Seed depth 

-

 Rear Roller

 

Summary of Contents for DRL-048








































Reviews: