Tapo RV20 User Manual Download Page 4

• Use appliances only with specifically designated battery packs. Use of any other battery packs may create a risk of injury and fire. 

• Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact accidentally occurs, flush with water. If 

liquid contacts eyes, additionally seek medical help. Liquid ejected from the battery may cause irritation or burns. 

• Do not use a battery pack or appliance that is damaged or modified. Damaged or modified batteries may exhibit unpredictable 

behavior resulting in fire, explosion or risk of injury. 

• Do not expose a battery pack or appliance to fire or excessive temperature. Exposure to fire or temperature above 130°C may cause 

explosion. 

• Follow all charging instructions and do not charge the battery pack or appliance outside of the temperature range specified in the 

instructions. Charging improperly or at temperatures outside of the specified range may damage the battery and increase the risk of 

fire. 

• Have servicing performed by a qualified repair person using only identical replacement parts. This will ensure that the safety of the 

product is maintained. 

• Do not modify or attempt to repair the appliance except as indicated in the instructions for use and care.

• Place the cords from other appliances out of the area to be cleaned.

• Do not operate the vacuum in a room where an infant or child is sleeping.

• Do not operate the vacuum in an area where there are lit candles or fragile objects on the floor to be cleaned.

• Do not operate the vacuum in a room that has lit candles on furniture that the vacuum may accidentally hit or bump into.

• Do not allow children to sit on the vacuum.

• Do not use the vacuum on a wet surface.

• Household use only

• The charging dock must only be supplied at safety extra-low voltage defined in the standard of EN 60335-1 corresponding to the 

marking on the charging dock. (for EU region)

• This charging dock can only charge lithium batteries and can only charge one battery at a time. The capacity of the battery does not 

exceed 2600mAh.

SAVE THESE INSTRUCTIONS

TP-Link hereby declares that the device is in compliance with the essential requirements and other relevant provisions of directives 

2014/53/EU, 2009/125/EC, 2011 /65/EU and (EU) 2015/863.The original EU declaration of conformity may be found at 

https://www.tapo.com/en/support/ce/

TP-Link hereby declares that the device is in compliance with the essential requirements and other relevant provisions of the Radio 

Equipment Regulations 2017.

The original UK declaration of conformity may be found at https://www.tapo.com/support/ukca/

Summary of Contents for RV20

























Reviews: