background image

BARRIER & STOP (BARR) 

Issue : 020913-B 

TPUK-GU31X 

   

14 

 

Operation 

 

 

To start the pump, apply compressed air to the pump and Guardian. 

 

The pump should continue to run until either 

1.

 

Air to the pump and/or Guardian is interrupted. 

2.

 

The Guardian experiences an increased pressure, above the set point, 
which is represented by the rest button of the Guardian being extended 
(see post trip actions detailed below) 

 

To stop the pump, interrupt the air to the pump and/or Guardian. 

 

 

Post trip actions 
 
If the Guardian trips the system must be regarded as in 
breach! 
 

Thereafter the pump, Guardian and associate pipe-work should be 
stripped, thoroughly cleaned and neutralized, checked and 
maintained before being returned to service. Refer to the 
‘Maintenance’ section of this manual for procedures to safely 
maintain the Guardian. Please refer to the pump manual for 
details on how to safely maintain the pump. 
 

 

 
The reset button can be used momentarily as an over-ride to 
purge the pump prior to maintenance, utilizing the back-up 
diaphragms. Press and hold the reset button for the duration of 
the purge, the button should oppose being pressed when the 
pressure exceeds the set point. The over-ride function should only 
be used under controlled conditions. 

 

 

 
Abuse of the reset/over-ride could result in failure of the 
back-up diaphragms, allowing media to escape through the 
pumps exhaust, causing risk to plant and personnel! 

 

 

 
Once the system has been rebuilt the set up procedure must be 
completed. Refer to set point adjustment section of this manual. 
(Page 13). 

 

 

Summary of Contents for Guardian system Mk3.1













































Reviews: