b) Setting the time and charging the battery
• Press and hold the M button (4) for approx. 3 seconds to switch on the portable charger.
• The time will be displayed. Press and hold the M button again for approx. 3 seconds to set
the time. Set the time using the
+ (3) and – (5) buttons.
• Press the M button again to switch from hours to minutes. The hours and minutes must be
entered within 3 - 4 seconds. Then the display switches back to the time of day.
•
Before first operation, it is recommended to fully charge the portable charger once. Press
the + or – button to display the battery charge status. The battery charge status is shown as
a percentage. The display shows 99% when the portable charger’s battery is fully charged.
After about 8 seconds, the display shows the time again.
•
Charge the portable charger as soon as the symbol for the low battery level appears (see
section a) LED display). The display with the icon for low battery status cannot be switched
off to ensure you are reminded to charge the portable charger.
•
Connect the Micro USB plug to the Micro USB port
(2)
. Connect the USB-A plug of the USB
charging cable to a USB-A port of a USB charger (not included in the delivery). Observe the
technical data.
A USB charger with 2 A is recommended for the input current of the portable charger.
If a lower input current is used, charging takes longer However, an input current
higher than 2 A does not reduce the charging time, since the input current is limited.
•
The charging time of the portable charger with a 2 A USB charger and a remaining battery
capacity of approx. 10% can be approx. 6 hours.
•
As soon as the battery is fully charged, the corresponding icon appears (see section a) LED
display).
•
Disconnect all the cables.
•
To turn off the LED display, double-click the
M button.
c) Charging a mobile device
• You can charge the portable charger while charging your mobile devices.
•
Connect the USB-A plug of the USB charging cable to one of the USB-A ports
(1). The
maximum charging current is distributed to the USB-A ports if both ports are used. Therefore,
check how much charging current your mobile device requires.
If the charging current of the connected devices exceeds the maximum output
current of the portable charger, the product switches off. The portable charger must
be recharged before continued use.
•
Connect the Micro USB plug to your mobile device.
•
The charging icon (mobile device charging) is displayed when a mobile device is connected
via USB. Press the
+ or – button to show the battery charge status of the portable charger
as a percentage for approx. 8 seconds. The LED display then switches back to the charging
icon.
• Press and hold the + button for about 3 seconds to turn off the display during charging.
• If the display is off, press the +, – or M buttons to turn on the display during charging.
•
Double-click the
M button to display the charging icon or the time.
•
Disconnect the USB charging cable from the portable charger and from the connected device
to pause or stop charging. When the connected mobile device is fully charged or the USB
charging cable is disconnected, the display shows the time.
•
Switch off the display by double-clicking the
M button, otherwise the time is displayed until the
internal rechargeable battery of the portable charger is empty.
•
The USB
output of the portable charger will turn off automatically after 15 seconds if no
button is pressed or no device is connected.
Care and cleaning
•
Before cleaning, disconnect the product from the connected devices
and from the power
supply. Switch off the LED display.
• Never use aggressive detergents, rubbing alcohol or other chemical solutions, as these may
damage the casing or cause the product to malfunction.
•
Use a dry, lint-free cloth to clean the product.
• Avoid contact with water or other liquids when cleaning.
Disposal
Electronic devices are recyclable waste and must not be placed in household waste.
Always dispose of the product according to the relevant statutory regulations.
You thus fulfil your statutory obligations and contribute to protection of the environment.
Technical data
Input voltage/current .....................
5 V/DC, 0.5 to 2 A
Output voltage/current ..................
5 V/DC, 0.5 to 2 A (per USB output)
max. 2.1 A combined for both USB outputs
Internal rechargeable battery ........
Lithium-polymer (Li-Po) 3.7 V / 10000 mAh
Operating conditions .....................
10 to +45 °C, 10 – 90 % RH
Storage conditions
........................
-20 to +45 °C, 10 – 90 % RH
Dimensions (L x W x H)
................
129 x 67 x 17 mm
Weight .......................................... 253 g
These operating instructions are published by CEI Conrad Electronic International (HK) Limited, 18th floor, Tower 2,
Nina Tower, no. 8 Yeung Uk Road, Tsuen Wan, New Territories, Hong Kong. All rights including translation reserved.
Reproduction by any method (e.g. photocopying, microfilming or capture in electronic data processing systems) requires
prior written approval from the editor. Reprinting, also in part, is prohibited. The operating instructions reflect the current
technical specifications at time of print.
Copyright 2018 by CEI Conrad Electronic International (HK) Limited
*1003LTF_1620602_v1_0418_02_hk_m_en
Distributed by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau
