background image

12.3 SECUR ET – VMB 

Wall Mounting Bracket 

 

 

 

 
 
 
 
 
 
 
 

 

The VMB is wall mounting bracket for the 
attachment of a VMY, available in both black 
and white finishes, allowing the user secure 
the Tannoy V12 loudspeaker in either portrait 
or landscape orientations to a wall. 
 
The Tannoy V12 loudspeaker is attached to 
the bracket using the accessories supplied. 
 
This wall-mounting bracket has a larger wall 
plate than previous models to maximise the 
integrity of fixing obtained. There are also two 
holes either side of the fixing beam to allow 
the speaker cable the pass through the wall 
plate and along the fixing beam to the terminal 
panel resulting in a more discrete installation. 
 
The fixing beam on the VMB has a number of 
mounting points from which the VMY can be 
attached at varying distances from the 
mounting surface. 
 

Only the screws, fasteners, shakeproof 
and plain washers specified on figure 3. 
should be used to assemble the VMB 
bracket

 

 
 

 
 

 

 

Number on Fig 3. 

Description 

Quantity 

VMB Wall Bracket 

M10 Nyloc Nut 

M10 Plain Washer 

30mm Square Blank Plug 

Nylon Spacer 

M10 x 85mm Screw 

 

FIG 2. 

FIG 3. 

FIG 1. 

 

  

!!

 

 

Summary of Contents for POWER V12


















Reviews: