manualshive.com logo in svg

Tannoy ACTIVE STUDIO MONITORS, Owner'S Manual

Share
Download
Tannoy ACTIVE STUDIO MONITORS Owner'S Manual Download Page 44

44

Technical Specifications- Precision 8 iDP

System (Master & Slaves)

System

3-Way semi-active near field monitor

Frequency Response 

(1) 

43Hz – 51kHz (+/- 2dB)

Max. SPL (@ 1m) 

(2)

 

120dB (continuous)

Dispersion (-6dB) 

90 degrees

Crossover Frequency 

1.7kHz (DSP generated) & 16kHz (passive)

Drive units 

200mm (8") Tannoy Dual Concentric™ constant directivity driver with
multiple fibre paper pulp cone.
25mm (1") titanium dome Wideband™ SuperTweeter™,
Neodymium magnet system

Cabinet LF Alignment 

Optimised bass reflex loaded

Dimensions (H x W x D) 

440mm x 272mm x 369mm (17

3

/

8

” x 10

3

/

4

” x 14

1

/

2

”)

Cabinet Construction 

MDF cabinet and front baffle, tongue and groove front and back
Black cabinet grey painted baffle with brushed aluminium inlay
Black anodized aluminum back plate

Total weight 

17 kg (37.4lbs)

Electronic System

Mains Voltage 

100 to 240Vac, 50 – 60Hz (auto – select)

Power Consumption 

45W @ 

1

/

8

 full power (IEC 6065)

Amplifier 

Bass/midrange – 200 Watts Class D
Tweeter & SuperTweeter™ 200 Watts Class D

System Sample Rates:

Internal 

96 kHz (except when slaved to digital input or word clock input)

External 

96, 88.2, 64, 48, 44.1 or 32 kHz (optional 192kHz)

Digital Section (Master only):

I/O connectors 

XLR (2 channels AES/EBU in). 3 x RJ45 proprietary TC LINK

Formats 

AES\EBU

Word clock 

Input BNC, 75 , 0.6 to 10 Vpp

Display 

2 x 16 character dot matrix

Operation 

Menu system / four buttons

Analogue Section (Master only):

Input connectors 

XLR balanced (pin 2+, pin 3-)

Impedance 

10/3 k  (balanced/unbalanced)

Selectable Full Scale Input Level 

+9, +15, +21, +27 dBu

Dynamic Range 

> 113 dB typ. (unweighted), BW: 20-20kHz

THD+N 

< -105 dB typ. @ 1 kHz, -3 dBFS

Cross-talk 

< -120 dB, 20 Hz to 20 kHz

A to D Conversion 

24 bit (Dual bit delta sigma sampling at 4.1/5.6/6.1/6.1MHz)

Slaves Only:

I/O connector’s 

2-x RJ45 proprietary TC LINK

The typical listening distance for 

Precision 8 iDP 

is 1.3 -2.8 m

The typical room size for 

Precision 8 iDP 

is 50-100 m3

NOTES

(1)

 

+/- 3 dB, measured at 1m in an anechoic chamber. 

(2

) 

Peak SPL at mix position for 1 pair driven.

Tannoy operates a policy of continuous research and development. The introduction of new materials or manufacturing methods will always equal or exceed the published
specifications which Tannoy reserve the right to alter without prior notice. Please verify the latest specifications when dealing with critical applications.

A C T I V E   S T U D I O   M O N I T O R S

Summary of Contents for ACTIVE STUDIO MONITORS

























































Reviews:

No comments

Brands by name

Popular brands

Load more brands