background image

TABLE 3-4

DIAGNOSTIC MODE OF OPERATION

DL

M4

M3

Ml

Test

Description of Test

Seek to  Track  0,  an d  turn  on  spindle  motor.  Th is  t e s t
seeks the  carriage  to  T r ack  0,  and  t u rn s  on  th e  spindle

motor. It 

may be  used to check the Track 0 status.

Seek to  Track  1,  and  turn  on  spindle  motor.  This  t e st
seeks the  carri age  to  T r ack  1,  and  t u rn s  on  th e  spindle
m otor.  It  m a y  b e  u s e d  f o r  i n d e x -to-data  b u rs t  t e s t i n g
with an  alignment  diskette.

Seek to  Track  3 8  f r o m  T r ack  0 ,  a n d  t ur n  o n  spindle
motor.  
T his  test  seeks  the  carri a ge  to  T r a ck  0,  t h en  t o
T rack  38.  I t  m a y  b e  u sed  for  r a d ia l  a l i g n m ent  a d j u s t -
ment with  an  alignment  diskette.

Seek to  Track  38  f rom  T r ack  76 ,  and  t urn  on  spindle
motor.  
This  test  seeks the  carriage  to  Track  7 6,  then  to
Track  38.  This  test,  along  with  th e  previous  one, is used
to measure hysteresis.

Seek to Track  76,  and  turn  on  spindle motor.  This  test
seeks the carriage  to  Track  76,  and  turns  on  the  spindle
motor.  Thi s  t es t  m a y  b e  u s e d  t o  c h ec k  i n d e x -to-data
b urst and azimuth .

Seek to Track  75,  and  turn  on  spindle motor.  This  test
seeks the carriage  to  Track  75,  and  turns  on  the  spindle

X

X

X

motor.

Toggle front panel L.E.D. with each revolution of the disk.
This  test  t oggles  the  f r on t  p a nel  L . E .D.  at  t h e  l e ading
edge of  each  side  zero  index  pulse.  A  si n gle-sided  disk
should be used for this  test.

Toggle front panel L.E.D. with each revolution of the  disk.
This  test  t o ggles  the  f r on t  p a nel  L . E .D.  at  t h e  l e ading

edge of each side one index pulse. A double-sided disk

should be used for this  test.

Alternate seek between Track 0 and Track 76 with spindle
motor  on.  
T h i s  t e st  c o n t i n u o usly  m o v es  t h e  c a r r i a g e

between  Tracks  0  an d  76 .  T hi s  t est  i s  u sed  to  exercise

the positioner system.

Seek to  Track  2,  and  monitor  the  Track  0  sensor.  This

test moves the carriage to Track 2, and displays the

s tate of  th e  T r ack  0  s ensor.  The  Track  0  sensor  sho"l d
change state at  Track  2.

X

3-15

Summary of Contents for TM848-1E



































Reviews: