manualshive.com logo in svg

TANDBERG E5780, Reference Manual

Share
Download
TANDBERG E5780 Reference Manual Download Page 30

  

Installing the Equipment 

Page 2-10 

Reference Guide: evolution 5000 E5780 and E5782 Encoder  

 

ST.RE.E10135.4 

 

 

 

 

 

Figure 2.5: Rear Panel Component Parts and Connectors 

2.6.2 

Connecting Up the Basic Encoder 

Once the unit has been installed in its intended operating position, it is ready to be connected 
up to the rest of the system equipment  
(see 

Figure 2.6

), providing it too has been installed (see 

page 2-11 

onwards

 

for pin-out details 

of the connectors). 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Figure 2.6: Equipment Connections for the Basic Unit 

Option Slot 

1

Option Slot 

2

Option Slot 

3

Option Slot 

6

Audio In 

and Audio 

Reference Out 

H Sync

Composite 

Video 

ASI  

Outputs 

RS-232

Data 

RS-422 

Data 

Alarm

RS-232/ RS-485 
Control 

SDI In

Ethernet

Technical 

 Earth 

HD SDI Input

E5780/E5782 Encoder

 

Video Input 

 
SDI IN 
 
HD SDI IN 
 
H SYNC 
 
COMP VIDEO 

Audio input

AES/EBU Reference

ETHERNET #1 
 
ETHERNET #2 
 
REMOTE CONTROL 

Audio Input  

Control  

RS-232 data input

RS-422 data input

Alarm and Fail Monitoring

 

DVB/ATSC Transport stream output

Output 

Alarm 

ASI OUT 1

ASI OUT 2

ASI OUT 3

ALARM

 

 

10BaseT

10BaseT

RS-232/RS-485

AUDIO IN 
 
 
 

DVB/ATSC Transport stream output 

DVB/ATSC Transport stream output 

SD Serial Digital Interface 

Analogue composite video

Studio Black and Burst 

Data  

RS-232 DATA 
 
RS-422 DATA 

HD Serial Digital Interface

Summary of Contents for E5780











































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands