TANDBERG D13187-03 User Manual Download Page 41

Page: 41 / 63

TANDBERG Gateway

Configure the Gateway

Static IP Address

The Static IP Address defines the network address of the gateway. This address is only used in static mode. Your
LAN administrator will provide you with the correct address for this field.

Static IP Subnet Mask

The Static IP Subnet Mask defines the type of network. Your LAN administrator will provide the correct value for
this field.

Static IP Gateway

The Static IP Gateway defines the Gateway address. Your LAN administrator will provide the correct value for this
field.

NTP

The NTP Service defines the address of the NTP server. Your LAN administrator will provide the correct value for
this field.

Save

When ready to store the new settings, press ‘Save’. These settings will take effect when the system is restarted.

Restart

This button will restart the gateway. Any changes made in IP Configuration and IP Service will then take effect.

Summary of Contents for D13187-03
































































Search results

Summary of Contents for D13187-03

Reviews:

Related manuals for D13187-03

Brands by name

Popular brands

TANDBERG D13187-03, User Manual

Search results

Summary of Contents for D13187-03

Reviews:

Related manuals for D13187-03

Brands by name

Popular brands