background image

2

LED behavior

Table 1 describes the behavior of the LEDs.

Table 1: ISDN gateway LED behavior

LED Color

Indicates

Compact Flash 
Activity 

Flashing 
green

One of:

the ISDN gateway is booting

a configuration change has been made

the configuration is being transferred by FTP

Console Link

Green

A PC is connected to the console port

Status

Green

The ISDN gateway is operating normally

Alarm

Red

The ISDN gateway is booting or has developed a 
fault, for example:

temperature is outside normal limits

fan failure

battery failure of the internal clock

Refer to the web interface for more information 
about the problem (go to 

Status > Health

)

ISDN Port Status, for each ISDN port:

L1

Off

There is no connection on this port, or the ISDN 
gateway is not receiving framing (also known as 
Red Alarm)

Flashing 
green

The ISDN gateway is receiving framing, but the far 
end is not receiving framing (also known as Yellow 
Alarm)

Green

The port is connected to the far end

L2

Green

Layer 2 connectivity has been achieved with the 
ISDN network from this port. This means that 
D-channel signaling has been established with the 
network

Act

Green

There is at least one active call using this port. 
Data is currently being received on this port

Summary of Contents for Codian GW 3201 Series



















Reviews: