background image

 
 
 

 
tanaka-usa.com

                                                            11                                            

 custsvc@tanaka-

ism.com

 

Owner’s Manual

 

TS-720 E-Z Tiller™ 

 
 
 
Trouble Shooting 
 

Engine Won't Start 

a. Engine does not turn over 

 

      

Battery is low          

#

 

Recharge Battery (see pg 8) 

 

      Switch not on          

#

 

Check Start Switch 

 

      Incorrect wiring       

#

 

Check electrical coupling connection 

 

 

 

(see page 4) 

 

b. Engine turns over 

 

           Incorrect Starting Procedure   

#

 

See Page 7

 

 

           No spark on spark plug  

   

#

 

Clean and re-gap plug (see pg 9) or replace 

                                                      

Not enough fuel                    

#

      

 

Add fuel 

                                                      

Fuel is old or incorrect           

#

    Replace with fresh fuel (see pg 6) 

 

Dirt in fuel tank                    

#

       

 Clean fuel tank 

 

Engine Lost Power

 

 

 

      

Carbon on muffler             

#

           

Clean (see pg 9) 

 

Too much oil in fuel 

 

#

 

Replace with proper fuel 

 

 Plugged air filter 

 

#

 

Clean (see pg 9) 

 

 Throttle is not open 

 

#

 

Squeeze the throttle lever

 

 

Tines Won’t Turn   

 

 

Incorrect Engine Installation      

#

        Reinstall engine (see pg 4) 

 

Foreign object lodged in tines    

#

        Clean Tines 

 

Engine speed too slow              

#

        See above (Engine Lost Power section.) 

 

Tines Rotate when

 

throttle is released 

                                                          Carburetor out of adjustment   

#

  Adjust idle speed (see pg 9) 

 

 Stiff throttle wire 

        

#

  Spray / oil throttle wire 

 
Unit does not till properly

 

 

 Incorrect tine installation              

#

       

Reinstall tines (see pg 5) 

                                                           Incorrect stabilizer bar installation  

#

     Adjust depth (see pg 8) 

 

Engine does not idle 

 

                            

Carburetor out of adjustment 

#

       

Adjust carburetor (see pg 9) 

 

 
 
 

 

 

Summary of Contents for TS-720













Reviews: