background image

 

 

 

www.tanakapowerequipment.com

                            1                                             

 [email protected] 

Owner’s Manual 

ECS-3301/3351 

 

 

 

 

 

Before using this unit: 

• 

Read the operator’s manual carefully. 

• 

Check that the cutting equipment is correctly assembled  

and adjusted. 

• 

Start the unit and check the carburetor adjustment.   

See “Maintenance”.

 

 

 

 

  

 

          

 

 

 
 
 

 

 
 
 
 
 
 
 
 
 
 
 
 
 

 
 
 
 
 

 

 

 
 
 
 
 

 

 
 
 

 
 

 

One-handed usage not permitted. 

While cutting, hold saw firmly with 

both hands with thumb firmly locked 

around front handle.

 

Warning, kickback danger. Be careful 

sudden and accidental upward and/or 

backward motion of the guide bar. 

NOTE! 

Only model ECS-3301C/3351C is approved under EU type examination. 

WARNING 

Read, understand and follow all 
warnings and instructions in this 

manual and on the unit. 

Always wear eye, head and ear 

protectors when using this unit. 

It is important that you read, fully understand and
observe the following safety precautions and
warnings. Careless or improper use of the unit
may cause serious or fatal injury. 

The engine exhaust from this product 

contains chemicals known to the State 

of California to cause cancer, birth 

defects and other reproductive harm.

 

Summary of Contents for ECS-3301





















Reviews: