background image

9096-311001

MODEL NO. AC311014

USER MANUAL  

Petrol Chain Saw

WARNING • PLEASE READ

Beware of kickback. Hold chain saw firmly with both hands when using. For your own safety, please read and follow
the safety precautions in this manual before attempting to operate your chain saw. Improper use can cause serious
injury.

This product has been tested at a computed kickback angle (CKA) of no greater than max. 45 degrees.

SAFETY • OPERATION • MAINTENANCE

AU

P E T R O L   C H A I N   S A W  W A R R A N T Y

The benefits conferred by this warranty are in addition to all other conditions and warranties in respect of

this product which the consumer may have taken under the Trade Practices Act 1974 or by any legislation

of a State or Territory of Australia. This product is warranted by Talon Tools Australia (ABN 12 099 520

939)(the “Company”) to be free from defects in material and workmanship for a period of 24 months from

the date of original purchase. The Company during the period of the warranty, will at its option, and subject

to the conditions stated herein, 

repair or replace

without charge this product or any component part, which

upon examination

by an Authorised Service Agent or by the Company is 

found to be defective

.

Wa r r a n t y   c o n d i t i o n s

This warranty will not apply:

(i)  where this product has been subjected to 

misuse, abuse, accident or want of care

;

(ii) where this product has been 

used for a purpose for which it was not designed

or is not suited;

(iii) where the service of this product has been 

undertaken by a person not authorised

by the Company

to carry out such work or where 

parts that have not been approved

by the Company have been used;

(iv) where this product has  been 

used for industrial purposes

.

Should service become necessary during the warranty period, the purchaser should contact an Authorised
Service Agent or the Company. In order to obtain warranty service, the purchaser must present the store
receipt showing the name of the retailer and the date of purchase together with a completed Warranty Card.
The period of the warranty begins from the original date of purchase, notwithstanding any  subsequent
repair or parts replacement. No additional warranty or guarantee other than set out in this document,
whether written or verbal, is authorised to be made on the Comapany's behalf. The purchaser shall be
responsible for delivery or causing the product to be delivered to the Compnay or the Authorised Service
Agent and  the purchaser shall be responsible for all charges in connection with re-delivery of the product
and/or the delivery of parts. Damage in transit is not covered by this warranty and purchasers should
remove from the product any liquids (if applicable) before sending and pack the product securely to prevent
damage.

Warranty exclusions

Normal wear par ts or components are subject to seperate terms as follows: Normal wear par ts,

components or service required when performing normal and regular maintenance of this prod-

uct are not covered by warranty unless it is found to be defective by an Authorised Service

Agent or by the Company. Normal wear par ts include, but are not limited to:

Chains.

Chain Bar.

Spark Plugs.

Carburetor Adjustments.

Lubricants.

Engine Tune-ups.

Filters.

Returns based on the above listed normal wear parts will not be accepted under this warranty as they
are considered consumable items and are at the expense of the purchaser.

1

Summary of Contents for AC311014









Reviews: