20
21
GB
•
FUEL MIXING TABLE
•
RECOMMENDED FUELS
Some conventional gasolines are being blended with oxy-
genates such as alcohol or an ether compound to meet
clean air standards. Your Talon engine is designed to
operate satisfactorily on any gasoline intended for auto-
motive use including oxygenated gasolines.
•
STARTING A COLD ENGINE
Fill fuel tank with proper gas and oil mixture. See FUEL
AND LUBRICATION. Set unit on ground so that it rests
on the back pack frame.
1. Pump primer bulb 10X by pressing up on the
bulb(D). (Fig. 10)
2. Your unit is designed with a 3 position choke: FULL
CHOKE “ ”, PARTIAL CHOKE “ ”, and RUN “ ”.
Move choke lever to FULL CHOKE “ ” position.
(Fig. 9)
3. Set throttle lock (C): While holding trigger (B) at
wide open position, press down and hold throttle
lock (C). Release throttle trigger (B), then release
throttle lock (C). Throttle trigger (B) will now remain
in the wide open position. Make sure ignition switch
is in the ON (I) position. (Fig. 11)
NOTE:
The unit uses the advance starting system with
MAX FIRE IGNITION™
, which significantly reduces the
effort required to start the engine. You must pull the starter
rope out far enough to hear the engine attempt to start.
There is no need to pull the rope briskly--there is no harsh
resistance when pulling. Be aware that this starting
method is vastly different from (and much easier than)
what you may be used to.
4.
With the unit on the ground, hold the top assist
handle and step on the bottom of the frame with foot.
(Fig. 12)
5.
Pull starter rope 4-6 times-if unit does not start
move choke lever to position 2 and pull 4-6 more
times (Fig. 13). Wait 10 sec. after unit starts then
move choke lever to position 3. (Fig.14)
6. Press trigger to run.
NOTE:
If engine fails to start after repeated attempts,
refer to Troubleshooting section.
NOTE:
Always pull starter rope straight out. Pulling
starter at an angle will cause rope to rub against the
eyelet. This friction will cause the rope to fray and wear
more quickly. Always hold starter handle when rope
retracts. Never let a rope snap back from extended
position. This could cause rope to snag or fray and also
damage the starter assembly.
•
IMPORTANT IDLING INFORMATION
In some cases due to operating conditions (altitude,
temperature etc.) your blower may need a slight
adjustment to the idle speed.
After warm up, If unit does not Idle after restarting 2
times, follow these steps to adjust idle.
1. Locate the idle adjustment screw (G) on the
carburetor (Fig. 15).
2. Using a Phillips or slotted screwdriver - turn screw
1/4 to 1/2 turn clockwise (to the right). Unit should
then idle properly.
•
STOPPING THE ENGINE
Emergency Stopping Procedure.
When it is necessary
to stop blower engine immediately, PRESS the OFF
“STOP
” switch (A) until the engine stops completely
(Fig.16).
Normal Stopping Method.
For normal stopping,
release trigger and allow engine to return to idle speed.
Then PRESS the OFF “STOP
” switch (A) until the
engine stops completely. (Fig. 16)
GASOLINE
TALON 40:1
PRESERVE
1 U.S. Gal.
3.2 oz.
95ml (cm
3
) .25 oz.
5 Liters
4.3 oz.
125ml (cm
3
) .30 oz.
1 lmp. Gal.
4.3 oz.
125ml (cm
3
) .30 oz.
Mixing Ratio 40 Parts Gasoline to 1 Part Lubricant
OPERATING INSTRUCTIONS
Fig. 9
Fig. 10
Fig. 11
D
A
C
B
Fig. 12
Fig. 13
Fig. 14
•
STARTING A WARM ENGINE
(Engine has
been stopped for no more than 15-20 min-
utes)
1. Set throttle latch (see step 2 for starting a cold
engine), pull starter rope briskly.
2. If engine does not start, or starts and then stops
after 5 rope pulls, follow procedure “STARTING A
COLD ENGINE”.
•
BLOWER OPERATIONS
1. Use the blower for trees, shrubs, flower beds, and
hard-to-clean areas.
2. Use the unit around buildings and for other normal
cleaning procedures.
3. Use the blower around walls, overhangs, fences,
and screens.
4. We recommend that a face mask be worn when
operating blower in dusty areas.
5. Stand away from the debris, at a distance that will
easily allow you to control the direction of blown
debris. Never blow debris in direction of bystanders.
6. To control velocity of air stream, blower can be
operated at any speed between idle and full throttle.
Experience with the unit will help you determine the
amount of airflow necessary for each application.
7. To reduce sound levels, limit the number of pieces of
equipment used at any one time.
8. Check your equipment before operation, especially
the muffler, air intakes and air filters.
9. Use rakes and brooms to loosen debris before
blowing.In dusty conditions, slightly dampen
surfaces when water is available.
10. Conserve water by using power blowers instead of
hoses for many lawn and garden applications,
including areas such as gutters, screens, patios,
grills, porches and gardens.
11. Use intermediate tube plus nozzle of your choice so
the air stream can work close to the ground.
12. After using blowers and other equipment, CLEAN
UP! Dispose of debris in trash receptacles.
•
OPERATION INSTRUCTIONS
1. Follow the instructions “STARTING A COLD
ENGINE”.
2. Once unit is running, place unit on your back by
slipping arms through the shoulder straps as if your
were putting on a jacket (Fig. 17).
3. When preparing to clear an area of debris, always
position yourself so that you can control the
direction debris will be blown .
4. The control handle (A)(Fig. 16) and the flexibility of
the blower tube assembly will allow you to clear the
most hard-to-reach areas .
5. The hand grip, throttle trigger, throttle lock and
ignition on/off switch (B) are all mounted on a swivel
handle that offers a wide range of operating
positions and comfort (Fig. 19).
•
AIR FILTER
To Clean Air Filter:
1.
Loosen knob (A)
holding air filter cover
in place, remove
cover (B) and lift filter
(C) from air box (Fig.
20 & Fig. 21).
2. Wash filter in soap and
water.
DO NOT USE
GASOLINE!
3. Air dry filter.
4. Reinstall air filter and air filter cover.
NOTE:
Replace filter if frayed, torn, damaged or unable to
be cleaned.
GB
WARNING:
Because of flying debris, always,
approved shielded safety glasses or face
shield when operating blower.
Fig. 16
A
Fig. 15
G
WARNING:
Before using your blower, review
Safety Precautions in your User Manual, and
all regulations for operation of the unit. These
precautions and regulations are for your pro-
tection.
WARNING:
DO NOT operate the blower with
other people or animals in the immediate
vicinity. Allow a minimum of 50 feet (15
meters) between operator and other people
or animals.
Fig. 17
Fig. 18
Fig. 19
MAINTENANCE INSTRUCTIONS
CAUTION:
NEVER operate blower without
the air filter or dust and dirt will be sucked into
the engine and damage it. The air filter must
be kept clean. If it becomes damaged, install
a new filter.
Fig. 20
B
A
Fig. 21
C
