Tally Dascom DL-820 User Manual Download

Page: 39 / 82

Tally Dascom DL-820

User Guide V1.0

2.7 Connect the interface

This printer provides USB and LAN interfaces for standard shipment. Parallel option is available.

You may decide to install additional interface to the backside of the printer.

The procedures to connect the standard interface:

1. Disconnect or switch off the power supplied to the printer.

2. Plug in one end of the interface cable to the corresponding interface port.

3. Plug the other end of the cable to the PC port.

Parts

Descriptions

Power socket

Connect to the connector on the power cord.

Power switch

Toggle it to turn the printer on or off.

USB interface

Communicate with the PC via USB connection. (standard
interface)

LAN interface

Communication with the LAN server. (standard interface)

）

Optional Interface

Reserve for the installation of option: parallel

Requirements for interface cables:

To prevent radio emission and interference, completely shielded cable with conductive connector

housing should be used. Consider the following factors to reduce emission/interference levels:



Use short interface cables. (Less than 1.5 m in length is recommended.)



Separate the interface cable from the power cord.



Avoid routing the interface cable within the power duct.

Power

switch

Optional

interface

Power socket

LAN interface

USB interface

Summary of Contents for DL-820



















































































Search results

Summary of Contents for DL-820

Reviews:

Related manuals for DL-820

Brands by name

Popular brands

Tally Dascom DL-820, User Manual

Search results

Summary of Contents for DL-820

Reviews:

Related manuals for DL-820

Brands by name

Popular brands