background image

5

1) L/MONO AND R

  Two unbalanced 2-pole phone jacks for stereo 

line input. Input level range: -10 dB. If the source 

signal is mono, connect to the L/Mono input jack 

only.

2) -10 dB ATTENUATOR

  Matches the output levels of sources connected to 

the mixer’s stereo input sockets. When switched 

on, the line input signal will be reduced -10 dB.

3) HI

  Controls the high-frequency equalizer boost or 

cut level. Max adjust range: +/-15 dB @ 12 KHz.

4) MID

  Controls the midrange-frequency equalizer boost 

or cut level. Max adjust range: +/-15 dB @ 2.5 KHz.

5) LOW

  Controls  the  low-frequency  equalizer  boost  or 

cut level. Max adjust range: +/-15 dB @ 80 Hz.

6) AUX

  Sends the channel signal to the AUX bus. The 

controlled signal is pre-fader so that the aux level 

is independent of the channel fader setting.

7) BAL (BALANCE) CONTROL

  Distributes the channel’s stereo signal level feed 

to the L/R buses. They are equal when the knob 

is in its center position.

8) LEVEL CHANNEL FADER

  This rotary fader controls the input channel’s 

output level feed to the MAIN bus, adjusting the 

volume balance relative to other channels.

STEREO CHANNEL

SECTION

CONTROL PANEL

Summary of Contents for MIX-06












Reviews: