Takstar ESC-15A User Manual Download Page 19

09

■  

Troubleshooting

Problems

Causes

Solutions

Power off.

Turn on the power switch

.

Volume knob is set to the minimum 
position

.

Increase the volume

.

No LF signal input.

Check the system connection or the 
equipment setting

.

The output of the power amplifier 
reaches its limit

.

Turn down the subwoofer or

 

the 

total

 

volume of the system

.

The frequency range of the power 
amplifier is too wide

.

Narrow

 

the frequency range

.

Distortion or 
abnormal sound 
in large dynamic

Overly dynamic sounds

 

(such as 

explosions) overload the subwoofer

.

Turn down the subwoofer or the 
total volume of the home theater 
equipment

 

appropriately

.

Buzz noise or 
AC noise

Connection problems or

 

grounding 

problems.

Refer to the user manual of the 
home theater equipment.

No sound

Bass distortion

      To avoid possible personal injury or property damage caused by electric shock, 
high temperature, fire, radiation, explosion, mechanical hazards, and improper use, 
please read and observe the following items before using the product.

1. When using the product, please confirm whether the power of the connected device 

matches the product power and adjust the device volume. Please do not use it for a 
long time when the product power is exceeded or at a high volume to avoid product 
failure and hearing damage.

2. If there is any abnormality (such as smoke, odor, etc.) during use, please turn off the 

power switch and unplug the power plug immediately, and then send the product to 
the dealer for maintenance.

3. The product and accessories should be placed indoors in a dry and ventilated place. 

Do not store them in a humid and dusty environment for a long time. Avoid getting 
close to the fire, liquids, rain, water, excessive collision, throwing, vibrating the 
machine, and covering the ventilation holes during use, so as not to damage its 
function.

4. If the product needs to be fixed on the wall or ceiling, please make sure to fix it in 

place to prevent it from falling.

5. When using the product, you must abide by the relevant safety regulations and do 

not use it on occasions that are prohibited by laws and regulations to avoid 
accidents. 

6. Please do not disassemble, refit, or repair the product by yourself to prevent 

personal injury. If you have any questions or service needs, please contact the local 
dealer for follow-up.

■  

Safety Instructions

ESC-15A

Active Subwoofer

Summary of Contents for ESC-15A






















Reviews: