④
No.06-073 C0055
,Q-DSDQ
Takex America Inc.
Takenaka Engineering Co., Ltd.
KWWSVZZZWDNH[HQJFRMS
Takex America Inc.
KWWSVZZZWDNH[FRP
Takex Europe Ltd.
KWWSVZZZWDNH[FRP
,QWKH86
,QWKH8.
,Q$XVWUDOLD
$YLDU\&RXUW:DGH5RDG
%DVLDPSVKLUH5*3(8.
7HO
)D[
+RZOH\V5RDGLOO
9,&
7HO
)D[
KWWSVZZZWDNH[FRP
*RMR'RUL6RWRNDQ1LJDVKLQR
<DPDVKLQDNX.\RWR-DSDQ
7HO
)D[
6DQ=HQR:$<
6XQQ\YDOH&$86$
7HO
)D[
Limited Warranty :
TAKEX products are warranted to be free from defects in material and workmanship for 12 months from original date of shipment. Our warranty does not cover damage or
failure caused by Acts of God (including inductive surge by lightning), abuse, misuse, abnormal usage, faulty installation, improper maintenance or any repairs other than
those provided by TAKEX. All implied warranties with respect to TAKEX, including implied warranties for merchantability and implied warranties for fitness, are limited in
duration to 12 months from original date of shipment. During the Warranty Period, TAKEX will repair or replace, at its sole option, free of charge, any defective parts
returned prepaid. Please provide the model number of the products, original date of shipment and nature of difficulty being experienced. There will be charges rendered for
product repairs made after our Warranty period has expired.
■OPTION：BL-5000
：BCW-401
：BP-150AE
7528%/(6+227,1*
(;7(51$/',0(16,216
63(&,),&$7,216
Solve possible problems according to the following table. If normal operations cannot be
restored by this means, contact either the dealer from whom you bought the unit or TAKEX.
Completely inactive
Sometimes inactive
(1)No power supply, broken wire or improper voltage.
(2)Not yet 1 minute after power turned on (Alarm LED is flickering.)
(3)Cover shielded by substances (including glass).
(4)Improper area adjustment.
(1)Improper area adjustment.
(2)Cover face is soiled with dust or water drop.
(3)Is the protection range proper ?
(4)Small temperature difference between people and back ground.
(1)Something moving in protected area or too rapid temperature variations.
(3)Intense reflection of sun light or head light shining on the sensor.
(4)Is the sensor reacting to passersby outside ?
(1)Poor contact output connection or broken wire or short circuit.
(2)Contact output is not working.
(3)Is the connected unit operation nomal ?
(1)Correct power supply or replace broken wire.
(2)Allow for warming up time (about 1 min.)
(3)Remove the substances.
(4)Readjust the protection area setting.
(1)Readjust the protection area setting.
(3)Reposition so that the range is proper.
(4)Set sensitivity 120%
(1)Remove the cause.
(2)Relocate device.
(3)Relocate device. Shield with a blind.
(4)Readjust the protection area.
(1)Check the wiring or connection.
(1)Check for disconnection or damage inside the device.
(2)Check the contact output terminal using a tester.
(3)Check the connected unit.
Mounting position
Ambient temperature range
Memory LED
Sensitive zone
Supply voltage
Coverage
Detection system
Model
Tapping screw : 2 pcs. Sensor locking screw : 1 pce.
PA-6614E
PA-6614E(BL)
The specifications are subject to change without notice.
(2)Clean the cover with soft cloth.
(Do not use chemicals such as thinners or alcohol.)
Activated when no person
has passed
The alarm LED lights, but
connected units are inactive
(2)Large electrical noise source such as power machine nearby or
its wiring close to that of sensor.
Trouble
Check
Corrective Action
Passive infrared (Twin mirror)
Wide angle 14m Max.
8mA Max.
38 pairs
7 to 30V DC (non-polarity)
Dry contact (Semi-Conductor)
(N.C. / N.O. selectable)
Reset : Approx. 2 sec., 24V (AC/DC) 0.25A
(protective resistor 3.3
Ω
)
3 minutes flashing, 47 minutes lighting and
automatically reset. (ON/OFF selectable)
Red : Flashing at warming up
Lighting at alarm (LED can be disabled)
Yellow : Flashing at memory activated
Lighting at memory indication
Vertically : 23°
Horizontally : 25°
(on mounting hole of base)
60% / 80% / 100% / 120% changeover
-15
℃
to +55
℃
(+5° F to +131° F) without condensation
Indoor ceiling
(wall mount with optional attachment BCW-401)
Accessory
Terminals on separate base unit
120g (4.23oz)
Body /Cover : White resin
Body /Cover : Black resin
Protection
Sensor unit
Base unit
φ120mm(φ4.72")
▲
▲
▲
▲
▲
▲
▲
▲
Wire hole
▲
▲
▲
▲
▲
▲
▲
▲
▲
▲
▲
▲
▲
▲
▲
▲
▲
▲
▲
▲
35
゜
35゜
35゜
35
°
R15mm
(R0.59")
Release lever
Locking
screw hole
φ98.5mm(φ3.88")
55mm(2.17")
8mm(0.31")
φ83.5mm(φ3.29")
66.7mm(2.60")
5-φ4.2mm
(φ0.17")
φ9mm
(φ0.35")
4.2mm(0.17")
34mm (1.34")
10.5mm
(0.41"
)
The alarm LED lights and
alarm signal output
continuously
(1)Self-diagnosis error.
Current consumption
Alarm signal
Alarm memory
Alarm LED
Adjustment
Sensitivity changeover
Self-diagnosis function
Temperature compensate
Other functions
N.C. 30V(AC/DC)0.25A
Wiring connection
Weight
Appearance
Tamper
