4
INSTALLATION
3
DO'S AND DON'T'S
5
WIRING
●
Install the sensor in a location
such that intruders are more likely
to cross the protection zones,
rather than approach head on.
●
Do not install in a site which
is subject to electrical noise or
intense vibration.
●
Avoid direct sunlight, spot light or
intense reflections on the sensor or
the protection zone.
●
Do not install the sensor outdoors
(indoor only).
[MAINTENANCE]
1.When the unit is soiled, clean the cover with a soft cloth
moistened with a small amount of cleansing -solution. Do not
use chemicals such as thinners or alcohol.
2.Check operation once a week. Do not fail to check operation
whenever furniture in coverage area is moved.
●
The passive infrared sensor is designed to detect infrared energy
variations caused by the presence of a human body. Therefore,
note that similar variations in conditions in protection area, due
to other reasons, may cause the sensor to create an alarm as it is
unable to distinguish between sources.
(1) Slide release lever
to a direction that
an arrow points to
detach sensor unit
from base unit.
(2) Mount the base on the ceiling with screws.
Fix so that the front mark ( ) is pointing to
the center of protection area.
＊
Break knockout
and put the wire
through wire
lead on base
unit, when
exposed wiring.
(3) Connect the wires to the terminals referring
to the paragraph on WIRING.
(4) Set the protection area referring to the
paragraph on PATTERN SETTING.
(5) Match up a front
mark on base unit
with that on
sensor unit.
Put a sensor unit
into a base unit
from front mark
side.
Push sensor unit until release lever will
clicks.
【
Basic connection
】
[When two units are used]
【
Allowable wiring distance between sensor and power source
】
Size of wire used
AWG 22 (Dia. 0.65mm)
AWG 20 (Dia. 0.80mm)
AWG 18 (Dia. 1.00mm)
Distance at 12VDC
820 ft. (250m)
1476 ft. (450m)
2296 ft. (700m)
Note 1) The maximum wire length, when two or more units are connected, is
the above distance divided by the number of units.
2) The protection circuit can be wired to a distance of 3,280 ft (1,000m)
with AWG 22 (0.65mm dia.) wire.
＊
Allow approx. one minute for warm-up after power is applied. (Alarm
LED is flashing) In the meantime, an alarm is not initiated.
＊
After the one minute has passed the unit will be in the armed condition
and will trigger when detecting a human body.
＊
All wiring should be in accordance with the national electric code NFPA-70.
Power
｝
Signal
input
＋
ー
Sensor (N.C.)
1
2 3
4
1
2 3
4
Sensor (N.C.)
①
②
(6) When sensor unit is detached, hold
it and slide release lever as
illustrated.
(7) When sensor unit is locked,
tighten the locking screw.
Sensor locking screw
Release lever
【
Terminal
arrangement
】
1
2
3
4
7
Alarm output
Dry contact (Semi-Conductor)
N.C. N.O. changeover
Reset : approx. 2 sec.
24V (AC/DC) 0.25A
(Protective resistor 3.3
Ω
)
Power (non-polarity)
10.5
〜
28V DC
25mA or less
(+2mA at L/C use)
Tamper
N.C.
30V(AC/DC)
0.25A
L/C
LED
Control
6
5
The power supply used with this unit
must have a minimum 4 hours
stand-by power capbillity.
※