manualshive.com logo in svg

Takagi T-D2-IN / 510, Installation Manual And Owner'S Manual

Share
Download
Takagi T-D2-IN / 510 Installation Manual And Owner'S Manual Download Page 34

34 

T-KJr2-IN / 110 & T-K4-IN / 310 T-D2-IN / 510

Malfunction description

Diagnosis

Red LED

TK-RE02

TM-RE30

Five Times

99

991

Imperfect combustion

• 

Check the gas type of the water heater 

matches the gas supplied to it .

• 

Inspect the environment around the 

water heater . Determine how long the 

unit has been installed .

• 

Check the altitude/elevation of the area 

of where the water heater is installed 

and match DIP switches .

• 

Check if there is any blockage in the 

intake air and/or exhaust . 

• 

If the water heater is installed as a 

direct-vent system, check whether there 

is enough distance between the intake 

air terminal and the exhaust terminal . 

• 

Check if there is grease and/or dirt 

in the burner (Part #101) and the fan 

motor (Part #103), especially if the 

water heater has been installed in a 

contaminated area .

• 

Check the DIP Switches match gas type 

of unit .

• 

Check the manifold pressure at Max . 

and Min .

• 

Check proportional gas valve hose .

Summary of Contents for T-D2-IN / 510













































Reviews:

No comments

Brands by name

Popular brands

Load more brands