Takagi Flash Water Heater T-KD20 Installation Manual And Owner'S Manual Download Page 19

 

19

 

 

 

 

 
 
 

 

Vapors from flammable liquids will explode and catch fire causing death or severe burns. 

Do not use or store flammable products such as gasoline, solvents or adhesives in the 

same room or area near the water heater. 

 
 

 

 
 
 
 

 

WARNING: Do not install water heater where flammable products will be stored.

 

Read and follow water heater warnings and instructions. If owner's manual is
missing, contact the retailer or manufacturer. 

 

WARNING

The outlet hot water temperature of the T-KD20 water heater is factory set 120 

°

F. 

WARNING: 

Use this heater at your own risk. The set outlet water temperature can cause 

severe burns instantly or death from scalds. Test the water before bathing or showering. 

Do not leave children or the infirm without supervised. 

DANGER

Hot Water Heater temperature over 125 

°

F can cause 

severe burns instantly or death from scalding. 
Children, disabled and elderly are at the highest risk of 
being scalded. 
Feel water temperature before bathing or showering. 
Temperature limiting valves are available, ask professional 
person.  

WARNING:

 California Proposition 65 lists chemical substances known to the state to 

cause cancer, birth defects, death, serious illness or other reproductive harm. This product 
may contain such substances, be their origin from fuel combustion (gas, oil) or 
components of the product itself. 

 

DANGER

Keep flammable products: 

1.  Far away from heater. 
2.  In approved containers. 
3. Tightly closed 
4.  Out of children's reach 

Vapors: 

1.  Cannot be seen 
2.  Vapors are heavier than air 
3.  Go a long way on the floor  
4.  Can be carried from other rooms 

to the main burner by air currents.

Summary of Contents for Flash Water Heater T-KD20






























Reviews: