Takagi 100 Series Page 18 Service Handbook Download

Page: 18 / 80

OUBLE

SHOO

TING

OUBLE

SHOO

TING

18 • On-Demand Water Heater Service Handbook for 240, 340 & 540 Condensing Models

replace the gas valve.

6. Check the voltage across the main

gas valve wires (blue - light blue

#3) during operation. The voltage

reading should be 93-120 VDC. If

the voltage is not within normal

range, replace the computer board.

Code 551: Abnormal Solenoid

Gas Valve (SV1, SV2, and/or

SV3)

This code indicates a driving circuit

fault for one or more of the solenoid

gas valves (SV1, SV2, or SV3).
1. Check the wire connections to the

gas solenoid valves for burns or

cuts.

2. If the unit was serviced recently

and the gas valve had to be

removed, make sure that each

gas valve wire is plugged into the

proper place. (For each connector,

the number stamped on the metal

must match the number that is

printed on the wire’s label. See

Figure 6, page 17.)

3. Verify that the supply gas pressure

is within the specified limits. Too

high of an inlet gas pressure may

cause the main gas valve to jam or

could be damaged.

4. With the power off, check the

resistance of each valve. Normal

resistance reading for SV1 and SV2

is 1.35-1.65 kΩ. Normal resistance

reading for SV3 is 2.07-2.53 kΩ.

If the resistance is out of range,

replace the gas valve.

5. Check the voltage across these

solenoid gas valve wires during

operation. (The dark blue wire is

common.)

•

SV1: Green (#9) & Blue

•

SV2: Orange (#53) & Blue

•

SV3: Red (#73) & Blue

In each case, the voltage reading

should be 93-120 VDC. If the

voltage is not within normal range,

replace the computer board.

Code 611: Abnormal Fan Motor

This code indicates a fan motor fault.
1. Disconnect power to the water

heater by unplugging it from the

wall outlet or turning it off at the

circuit breaker.

2. Check venting for blockages or for

the presence of contaminants in

the water heater area (e.g., lint,

dust). Make sure that there are

no contaminants inside the water

heater cabinet. Correct any issues

that are found.

3. Visually check for breakages in the

fan motor wiring or burn marks on

the computer board (PCB). Repair/

replace as needed.

4. Check for leaks at the heat

exchanger.

5. Check the fan housing for water.

6. If you found water in the fan

housing, clean and dry the fan. To

remove the fan,

make sure that

power to the water heater is

still turned off

, then follow steps

8.1 through 8.1.2 on page 41.

Reassemble in reverse order.

7. Turn on power to the water heater,

then test the heater.

8. Complete this step only if the previous

steps did not solve the issue.

During operation, check the voltage

between the fan motor wires listed

below. The blue wire is common. (See

“FM” in the wiring diagram, page 30

or 31.)

•

Red & Blue

Normal: 132 to 192 VDC

(during operation)

•

Yellow & Blue

Normal: 13 to 17 VDC

(during operation)

•

Orange & Blue

Normal: 2 to 6.5 VDC

(during operation)

If the voltage readings fall within the

normal range, replace the fan motor.

If the voltage readings are not within

normal range, replace the computer

board.

Code 651: Flow Adjustment Valve

Fault (Easy-Link or Multi-Link

System only)

This code indicates a flow adjustment

valve fault.
1. Inspect the flow adjustment valve

(item number 402, p. 74) for the

following:

•

Broken or disconnected wires

•

Debris or scale buildup inside the

valve assembly that would prevent

the valve from opening or closing

•

Water leakage at the flow

adjustment valve (Replace the

seals/component.)

2. Check the resistance of the flow

adjustment valve. To check it,

a.)

turn off electrical power to the

water heater, then

b.)

unplug the flow

adjustment valve’s connector from

the computer board. (See schematic

on page 30 or 31.)

c.)

Check the

resistance between the red and black

wires. Normal resistance (black-red):

90 to 200 Ω. If the resistance is out of

range, replace the flow adjustment

valve.

3. Check the voltage of the flow

adjustment valve where its connector

plugs into the PCB. Measure between

Summary of Contents for 100 Series
















































































Search results

Summary of Contents for 100 Series

Reviews:

Related manuals for 100 Series

Brands by name

Popular brands

Takagi 100 Series, Service Handbook

Search results

Summary of Contents for 100 Series

Reviews:

Related manuals for 100 Series

Brands by name

Popular brands