CHAPTER 8 PARAMETER SETTING
83
11. Frame Back All Head Sew
12. Overlap Frame Back
13. Halt Frame Back
14. ------
15. Min. Revolution [rpm]
(GC02)
Make the machine perform embroidery with all
heads when the machine starts after frame back.
Yes
To perform embroidery with all
heads
No
Only the head where thread
breakage occurred performs
embroidery
No
No
No
600
2
4
70
Yes
30
(Yes/No)
No
( No, Yes, )
( No, 1, 2, 3, 4, 5, 6, 7, 8, 9, )
( No, Yes, )
------
( 250 ~ 700, )
( 0, 1, 2, 3, 4, )
( 0, 2, 4, 6, 8, )
18. Under T.D. (Step Ratio) [%]
( 40, 50, 60, 70, 80, )
( No, Yes, )
20. Picker Timing (Tail Length)
( 340 ~359, 0 ~ 60 deg, )
It makes all-head sewing from set number of
stitches prior to the detecting point of thread
breakage when the machine starts after frame
back.
It is effective when “11. F.B. All Head Sew”
is set to “No”.
“No” performs all head embroidery from
thread breakage detecting point
(No/ 1~9)
No
No
No
600
2
4
70
Yes
30
No
( No, Yes, )
( No, 1, 2, 3, 4, 5, 6, 7, 8, 9, )
( No, Yes, )
------
( 250 ~ 700, )
( 0, 1, 2, 3, 4, )
( 0, 2, 4, 6, 8, )
18. Under T.D. (Step Ratio) [%]
( 40, 50, 60, 70, 80, )
( No, Yes, )
20. Picker Timing (Tail Length)
( 340 ~359, 0 ~ 60 deg, )
When starting the machine after frame back, make
the machine stop at all head sewing start point.
Yes
To stop
No
No to stop
(Yes/No)
No
No
No
600
2
4
70
Yes
30
No
( No, Yes, )
( No, 1, 2, 3, 4, 5, 6, 7, 8, 9, )
( No, Yes, )
------
( 250 ~ 700, )
( 0, 1, 2, 3, 4, )
( 0, 2, 4, 6, 8, )
18. Under T.D. (Step Ratio) [%]
( 40, 50, 60, 70, 80, )
( No, Yes, )
20. Picker Timing (Tail Length)
( 340 ~359, 0 ~ 60 deg, )
It is not applied.
No
No
No
600
2
4
70
Yes
30
( No, Yes, )
( No, 1, 2, 3, 4, 5, 6, 7, 8, 9, )
( No, Yes, )
------
( 250 ~ 700, )
( 0, 1, 2, 3, 4, )
( 0, 2, 4, 6, 8, )
18. Under T.D. (Step Ratio) [%]
( 40, 50, 60, 70, 80, )
( No, Yes, )
20. Picker Timing (Tail Length)
( 340 ~359, 0 ~ 60 deg, )
Lower limit of operating r.p.m.
Inching is not included.
(250 ~ 700)
No
No
No
600
2
4
70
Yes
30
600
( No, Yes, )
( No, 1, 2, 3, 4, 5, 6, 7, 8, 9, )
( No, Yes, )
------
( 250 ~ 700, )
( 0, 1, 2, 3, 4, )
( 0, 2, 4, 6, 8, )
18. Under T.D. (Step Ratio) [%]
( 40, 50, 60, 70, 80, )
( No, Yes, )
20. Picker Timing (Tail Length)
( 340 ~359, 0 ~ 60 deg, )
Summary of Contents for TEHX-C
