manualshive.com logo in svg

Tajfun Planina EGV 45AHK, Operating Instructions Manual, Page: 16 / 24

Share
Download
Tajfun Planina EGV 45AHK Operating Instructions Manual Download Page 16

16 

4.8. CHECKING AND TIGHTENING THE DRIVE CHAIN                                          (Figure 9) 

 
During the operation and under the load, the drive chain stretches, therefore the operator 
must check and readjust the chain periodically to prevent excessive wear of the whole chain 
drive. The chain must not be set to tight and chain slack should be set 1 to 3 mm. The 
shorther chain should allow ±1 mm slack and the longer chain ±3 mm. Check the tightness of 
the chain by hand, pushing the chain between the chain wheels. 
 
Procedure: 



If the winch is connected to the tractor, shut down the tractor and disconnect the PTO shaft.  



Unscrew the screw 

3

 and remove the chain cover 

4 

by pushing it upwards.  



Loosen both screws 

5

 by approximately one turn, to move the drive chassis 

8

.                               



First tighten the shorter chain 

2

 using the tensioning screw 

7 

and counter nut 

6

. Screw the 

counter nut tightly, afterwards. The slack of the shorter chain should be ±1 mm. 



Tighten the longer chain 

12

 by screwing the nut on the tightening screw 

1

 until you reach 

the desired chain slack: ±3 mm. 



Screw the screws 

5

 tightly. 



Lubricate the chain using special chain lubrication spray.  

Summary of Contents for EGV 45AHK

























Reviews:

No comments