Tait TP8135 User Manual Download Page 18 | Manualshive

Page: 18 / 120

background image

18

Vehicle charger installation and operation

For detailed instructions necessary to the safe installation and
operation of the vehicle charger, please refer to the
documentation supplied with the vehicle charger.

Electromagnetic compatibility in European vehicles

In the European Community, radio equipment fitted to automotive
vehicles is regulated by Directive 72/245/EEC and its amendments.
The requirements of this directive cover the electromagnetic
compatibility of electrical or electronic equipment fitted to
automotive vehicles.

Unapproved modifications or changes to radio

The radio is designed to satisfy the applicable compliance
regulations. Do not make modifications or changes to the radio
that are not expressly approved by Tait Limited. Failure to do so
could invalidate compliance requirements and void the user’s
authority to operate the radio.

Attaching of labels

Warning

Do not obstruct the vent hole on the battery or the vent

hole on the radio chassis label. If the vent on the battery is
obstructed the battery may explode, causing personal injury
and/or damage to property. If the vent on the radio is obstructed,
audio quality and/or key function may deteriorate and radio seals
may be damaged.

Notice

Tait Limited recommends that you do not affix additional

labels to the surfaces between the radio chassis and the battery.
The fit between these surfaces is intentionally firm and any added
thickness will damage the points of attachment between radio
and battery. If you must attach a customized label, use only a thin
gummed paper label applied to the bottom 25% of the radio
chassis label and/or to the top 25% of the battery label. Do not
obstruct the vent holes (see Warning above). Do not allow the

«
...
16
17
18
19
20
...
»

Summary of Contents for TP8135

























































































































Reviews:

No comments

Related manuals for TP8135

Brand: unicraft Pages: 60

Brand: Raymarine Pages: 54

Brand: Raymarine Pages: 46

Brand: Yaesu Pages: 2

Brand: Yaesu Pages: 2

Brand: Blaupunkt Pages: 57

Brand: tez audio Pages: 4

Brand: Parker Pages: 30

Brand: ION Pages: 56

Brand: Dr.Prepare Pages: 16

Brand: Denver Pages: 80

Brand: Sylvania Pages: 12

SKYLINE HFP3000

Brand: INE Pages: 96

Brand: Cobra Pages: 11

Brand: NXP Semiconductors Pages: 2

Brand: Muse Pages: 14

Brand: BC Pages: 19

Brand: Sencor Pages: 76

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands